04-03-2009
how to force e1000g0 interface in solaris 10
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
Anyone have any solution for this please help.
Million thanks.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Does any body knows how to force NIC to 100 Full Duplex in Solaris 8, should survive after reboot or shutdown. (1 Reply)
Discussion started by: s_aamir
1 Replies
2. Cybersecurity
Does any body knows how to force NIC to 100 Full Duplex in Solaris 8, should survive after reboot or shutdown. (2 Replies)
Discussion started by: s_aamir
2 Replies
3. UNIX for Advanced & Expert Users
Double question here ... Running on Debian Etch and Apache 2.0
1) Using mod_proxy and/or mod_proxy_http in apache 2.0.
The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies
4. Solaris
Hi all,
I would like to force the LAN card to use 10MB instead of 100MB in UNIX enviroment, please help. thanks! :) (3 Replies)
Discussion started by: Felixkoo
3 Replies
5. Solaris
Hi All,
Can someone share with me how to force umount in solaris 2.6?
Thanks
Leong (3 Replies)
Discussion started by: bkleong
3 Replies
6. Shell Programming and Scripting
Hello All,
Can someone show me how to cat "only the IP address of e1000g0" using ifconfig -a.
i am trying to grep only the ip address (xx.xx.xx.xx) from the bunch of all other things like, broadcast address, IPV4, UP........and so on.
thanks (1 Reply)
Discussion started by: solaix14
1 Replies
7. Solaris
hi all
I need to add a user "abcd" and set the password same as the user id. But Solaris 8 is not allowing me to do it, is there any way we can force the password to be same as the user id.
Any help would be appreciated.
Thanks
bash-3.00# cat /etc/release
... (9 Replies)
Discussion started by: imran721
9 Replies
8. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
9. Solaris
Hello all,
I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0.
This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help.
Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies
10. Solaris
Hi All,
Please let me know the step by step process to set the e1000g0 interface speed to 1000mbps with full duplex from 100fdx and how to disable the auto negotiation with switch?.
Thanks and Regards,
Ganesh. (7 Replies)
Discussion started by: gsrungav
7 Replies
ndd(1M) System Administration Commands ndd(1M)
NAME
ndd - get and set driver configuration parameters
SYNOPSIS
ndd [-set] driver parameter [value]
DESCRIPTION
ndd gets and sets selected configuration parameters in some kernel drivers. Currently, ndd only supports the drivers that implement the
TCP/IP Internet protocol family. Each driver chooses which parameters to make visible using ndd. Since these parameters are usually
tightly coupled to the implementation, they are likely to change from release to release. Some parameters may be read-only.
If the -set option is omitted, ndd queries the named driver, retrieves the value associated with the specified parameter, and prints it. If
the -set option is given, ndd passes value, which must be specified, down to the named driver which assigns it to the named parameter.
By convention, drivers that support ndd also support a special read-only parameter named ``?'' which can be used to list the parameters
supported by the driver.
EXAMPLES
Example 1: Getting Parameters Supported By The TCP Driver
To see which parameters are supported by the TCP driver, use the following command:
example% ndd /dev/tcp ?
The parameter name ``?'' may need to be escaped with a backslash to prevent its being interpreted as a shell meta character.
The following command sets the value of the parameter ip_forwarding in the dual stack IP driver to zero. This disables IPv4 packet forward-
ing.
example% ndd -set /dev/ip ip_forwarding 0
Similarly, in order to disable IPv6 packet forwarding, the value of parameter ip6_forwarding
example% ndd -set /dev/ip ip6_forwarding 0
To view the current IPv4 forwarding table, use the following command:
example% ndd /dev/ip ipv4_ire_status
To view the current IPv6 forwarding table, use the following command:
example% ndd /dev/ip ipv6_ire_status
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
nca(1), ioctl(2), attributes(5), arp(7P), ip(7P), ip6(7P), tcp(7P), udp(7P)
NOTES
The parameters supported by each driver may change from release to release. Like programs that read /dev/kmem, user programs or shell
scripts that execute ndd should be prepared for parameter names to change.
The ioctl() command that ndd uses to communicate with drivers is likely to change in a future release. User programs should avoid making
dependencies on it.
The meanings of many ndd parameters make sense only if you understand how the driver is implemented.
SunOS 5.10 8 Nov 1999 ndd(1M)