How to force the LAN interface running on 10M

Thread Tools Search this Thread
Operating Systems Solaris How to force the LAN interface running on 10M
# 1  
Old 01-23-2008
How to force the LAN interface running on 10M

Hi all,

I would like to force the LAN card to use 10MB instead of 100MB in UNIX enviroment, please help. thanks! Smilie
# 2  
Old 01-23-2008
use this script:
read the first few lines on how to use it!
# 3  
Old 01-23-2008
box[root]# ndd -get /dev/ce \?

? (read only)
instance (read and write)
adv_autoneg_cap (read and write)
adv_1000fdx_cap (read and write)
adv_1000hdx_cap (read and write)
adv_100T4_cap (read and write)
adv_100fdx_cap (read and write)
adv_100hdx_cap (read and write)
adv_10fdx_cap (read and write)
adv_10hdx_cap (read and write)
adv_asmpause_cap (read and write)
adv_pause_cap (read and write)
master_cfg_enable (read and write)
master_cfg_value (read and write)
use_int_xcvr (read and write)
enable_ipg0 (read and write)
ipg0 (read and write)
ipg1 (read and write)
ipg2 (read and write)
rx_intr_pkts (read and write)
rx_intr_time (read and write)
red_dv4to6k (read and write)
red_dv6to8k (read and write)
red_dv8to10k (read and write)
red_dv10to12k (read and write)
tx_dma_weight (read and write)
rx_dma_weight (read and write)
infinite_burst (read and write)
disable_64bit (read and write)
accept_jumbo (read and write)
laggr_multistream (read and write)

/dev/ce adv_10hdx_cap -- half dup
/dev/ce adv_10fdx_cap --full dup

box[root]# ndd -get /dev/ce adv_10hdx_cap
box[root]# ndd -get /dev/ce adv_10fdx_cap

use ndd to set it to 1, read man pages how to use ndd. Then add the ndd command into S99ndd in rc3.d so everything it reboot it will set to 10m
# 4  
Old 01-23-2008
Thanks DukeNuke2 & sparcguy. The solution works.Smilie
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Solaris

Interface e1000g0 not showing in running state

Hello all, I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0. This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help. Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies

2. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

3. Red Hat

iptable port forwarding between two lan interface

Hi, How can I config iptables to allow port forwarding from one WAN interface to second lan interface . In my system I have one wan interface (eth0),and lan interface I want to make port forward port no 22 from to port 22 , , tcp and udp... (1 Reply)
Discussion started by: chuikingman
1 Replies

4. Red Hat

blue screen to config lan interface

I use red hat linx ES 4 ,5 , how can I start up attached screen to config the lan interface in command mode ??? Please advice in detailed ?? (1 Reply)
Discussion started by: chuikingman
1 Replies

5. IP Networking

Local Lan, no-ip directed DNS forward, surf within lan

Hi, We have a website running on a local centos 5.4 surfer, static IP. The uses to take care of the DNS, it forwards all to my server. My router receives the port 80 call, routes it to my server and the world can see perfectly fine. However, we cannot see... (3 Replies)
Discussion started by: lawstudent
3 Replies

6. Solaris

how to force e1000g0 interface in solaris 10

Hi all, I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot. But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands. ... (1 Reply)
Discussion started by: mailbox80
1 Replies

7. IP Networking

Solaris 9 new pumbed interface will not enter a RUNNING state

I'm trying to plumb a new interface bge1 on my machine: root@obms2-com-indianapolis-in:/root# ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet... (3 Replies)
Discussion started by: R37ribution
3 Replies

8. UNIX for Advanced & Expert Users

Double question: Apache mod_proxy and force connection over specific interface

Double question here ... Running on Debian Etch and Apache 2.0 1) Using mod_proxy and/or mod_proxy_http in apache 2.0. The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies

9. Solaris

How to configure private LAN and coporate LAN on the same machine-Solaris10

Hi , I am trying to configure a private LAN and corporate LAN on the same machien on Solaris 10. How can I achieve this? Thanks (1 Reply)
Discussion started by: deedee
1 Replies
Login or Register to Ask a Question