03-02-2009
Dual port NIC, cfgmgr
OS: AIX 6.1
The host has a dual port NIC installed and when I went to run `cfgmgr -v` to configure it I got an error showing device packages are missing from the install:
`cfgmgr -v` on 10.15.xx.xxx
cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed.
Quote:
devices.pci.ethernet:devices.pci.pci8086.1079.8086.1179.3:devices.pci.8680791086807911:dev
ices.pci.86807911:devices.pci.pci8086.1079.3:devices.pci.86807910:devices.pci.pciclass.020
000:devices.pci.pciclass.000200
Configuration time: 23 seconds
Any assistance or suggestions, greatly appreciated. Very much an AIX n00b.
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have a problem with a server disconnecting from the network.
This is a SUN box with dual NIC's running Solaris 8.
We have a Nokia router that routes traffic but it's virtual address doesn't respond to pings. When the SUN box sends out a ping, if nothing comes back it will shut down... (5 Replies)
Discussion started by: m_smith
5 Replies
2. IP Networking
I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB?
Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
Discussion started by: jwholey
0 Replies
3. Solaris
Greetings Forumers!
I am running into an issue with multiple zones on an M5000 with 2 NICs. The NICs are on separate VLANs. These zones are using the 2 NICs to communicate with other systems but when they need to communicate with a zone on the same system, but different NIC, the application... (9 Replies)
Discussion started by: bluescreen
9 Replies
4. AIX
All
I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable:
$ lsnports
name physloc ... (4 Replies)
Discussion started by: johnf
4 Replies
5. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. AIX
Hi,
From the man page, cfgmgr configures devices and optionally installs device software by running the programs specified in the Configuration Rules object class and it is not dependent on platform .
Are there any fundamental differences impacting the speed of cfgmgr on a stand-alone and... (5 Replies)
Discussion started by: Sachin1987
5 Replies
8. AIX
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Discussion started by: gps1976
1 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
10. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
EAP(4) BSD Kernel Interfaces Manual EAP(4)
NAME
eap -- AudioPCI audio device driver
SYNOPSIS
eap* at pci? dev ? function ?
audio* at audiobus?
joy* at eap?
midi* at eap?
options EAP_USE_BOTH_DACS
DESCRIPTION
The eap driver provides support for the Ensoniq AudioPCI and Creative Labs SoundBlaster PCI series of audio cards. All models based on the
ES1370, ES1371, and ES1373 chips are supported.
By specifying:
options EAP_USE_BOTH_DACS
a second audio device is attached. You can use it simply by directing audio output to it. This way it is possible for two different pro-
grams to use the "same" audio device simultaneously.
SEE ALSO
ac97(4), audio(4), joy(4), midi(4), pci(4)
HISTORY
The eap device driver appeared in NetBSD 1.4.
CAVEATS
The joystick port hardware works by emulating a legacy isa(4) joystick port, bypassing the pci(4) bus method for address allocation. This is
unlikely to work on PCI busses other than the primary one. There is also a possibility for conflicts with real ISA devices because the PCI
bus is probed before ISA. Use with caution.
BSD
July 22, 2006 BSD