02-24-2009
No, you need 2 virtual interfaces for load balancing (active/active), as the data (or virtual) i.p. needs to bind to a dedicated physical NIC. With only a single VIP, you need to configure for an active/passive connection which deals with failover, not increased throughput..
8 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
hi all
need your help.
I am wrting a script that will load data into the table.
then on another load will append the data into the existing table.
Regards
Ankit (1 Reply)
Discussion started by: ankitgupta
1 Replies
2. Solaris
Hi everybody,
One client asked me to configure network failover and load balancing for two Ethernet interfaces, I tried IPMP but I was unable to do so, because he's using his Gateway as firewall and PING is disabled.
so IPMP kept telling me that all interfaces failed because gateway can't be... (8 Replies)
Discussion started by: Sun Fire
8 Replies
3. Solaris
Is it possible to do a load balancing ( incoming and outgoing )with with IPMP in solaris 10 like sun trunking ? If yes what are the steps involved in it , i know how to do the failover IPMP both link based and probe based but i 'm looking for possible load balancing (3 Replies)
Discussion started by: fugitive
3 Replies
4. Solaris
Hi,
I need to configure 4 ip address (same subnet and mask) in one ipmp group (two interfaces) in an active active formation (link based). Can some one provide the steps or a tutorial link.
Thanks (2 Replies)
Discussion started by: Mack1982
2 Replies
5. Solaris
Hi,
This may have already been raised previously so sorry for the duplication. What I want to achieve is have a physical server using link based IPMP setup in the global zone (not problem doing that) and then create a zone set as Shared-IP so when the servers NIC has an issue the IP will... (0 Replies)
Discussion started by: giles.cardew
0 Replies
6. Solaris
Hi
I would like to know whether we can configure link based IPMP in private connectivity in Oracle RAC
Regarsd
---------- Post updated at 04:35 PM ---------- Previous update was at 04:27 PM ----------
Here I am taking about in case of private connectivity through cross cable (6 Replies)
Discussion started by: sb200
6 Replies
7. UNIX for Advanced & Expert Users
With linux kernel 2.4.22-1.2199.nptlsmp (I know, it's very old) Sometimes Load average increases to big value (over 7) but my 4 vCPU are in
idle state (5% busy every cpu). My web procedure was gone down so I found out that process (with 4732 process id, see my following output)
was in... (4 Replies)
Discussion started by: zio_mangrovia
4 Replies
8. AIX
Hi Admins,
I am having a whole system lpar in open firmware state on HMC.
How can I bring it to running state ?
Let me know. Thanks. (2 Replies)
Discussion started by: snchaudhari2
2 Replies
LEARN ABOUT HPUX
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)