|
|
Sponsored Content
Operating Systems
AIX
Processor and processor core
Post 302287071 by raba on Thursday 12th of February 2009 04:31:22 PM
02-12-2009
|
|
8 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi Everyone
I am new to unix. I ahve few quries that i would like to post.
Is there any way by which i get the unique processor Id. Actually i am unable to find any logic and method to get access to Processor Id.
Is it possible to get it. I read it on Intel site that the new processor do no... (1 Reply)
Discussion started by: atul.saxena
1 Replies
2. AIX
Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities.
Environment is a 8-way p570 with 4 LPARs.
lparVIO1 and lparVIO2:
AIX 5300-04-01
Mode/Type= Shared-SMT/Capped
Minimum Processors= 0.10
Desired Processors= 0.50
Maximum... (1 Reply)
Discussion started by: guttew
1 Replies
3. Linux
hi all
I bought a new MSI motherboard and intel dual core processor .
i have currently installed fedora core 3 for which audio is not detected .
can u tell me which version of fedora core will support as i have tried with
fedora core 6 which gets installed but gives a error while... (0 Replies)
Discussion started by: nageshrk
0 Replies
4. Red Hat
Hi,
what is command to find out no of core per procssor?
Regards,
Manoj (4 Replies)
Discussion started by: manoj.solaris
4 Replies
5. Linux Benchmarks
CPU/Speed: AMD Phenom(tm) 9950 Quad-Core Processor
Ram: 3.6 GB
Motherboard: Foxconn 7da-s
Bus:
Cache:
Controller:
Disk:
Load:
Kernel: Linux 2.6.26-2-amd64
Kernel ELF?:
pgms:
==============================================================
BYTE UNIX Benchmarks (Version... (0 Replies)
Discussion started by: migracho
0 Replies
6. HP-UX
hi every body
i want to know if i have server with hp-ux os if i did "machinfo" i will see no of cpu = for example 16
how can i know this is dual or quad core .
thanks (2 Replies)
Discussion started by: maxim42
2 Replies
7. Shell Programming and Scripting
hi,
what plugins i need to install to run m4 processor in bash shell. Also, what is the file extension for m4 processor ( like .cc in c ).
Thanks (1 Reply)
Discussion started by: Learnerabc
1 Replies
8. UNIX for Dummies Questions & Answers
hello Admins,
how to find number of processor in unix machine. (2 Replies)
Discussion started by: vipinkumarr89
2 Replies
LEARN ABOUT NETBSD
tr
TR(4) BSD Kernel Interfaces Manual TR(4) NAME
tr -- TROPIC based shared memory Token-Ring cards device driver SYNOPSIS
tr0 at isa? port 0xa20 iomem 0xd800 irq ? tr* at isa? port ? irq ? tr* at isapnp? tr* at mca? slot ? tr* at pcmcia? function ? DESCRIPTION
The tr device driver supports TROPIC I based shared-memory Token-Ring cards. HARDWARE
Supported cards include the following IBM and 3Com models: IBM Token-Ring Network PC Adapter IBM Token-Ring Network PC Adapter II IBM Token-Ring Network Adapter/A IBM Token-Ring Network 16/4 Adapter IBM Token-Ring Network 16/4 Adapter/A IBM Token-Ring 16/4 Credit Card Adapter IBM Token Ring Auto 16/4 Credit Card Adapter IBM Turbo 16/4 Token Ring PC Card IBM 16/4 ISA Adapter IBM Auto 16/4 Token-Ring ISA Adapter IBM Token Ring 16/4 Credit Card Adapter IBM Token Ring Auto 16/4 Credit Card Adapter IBM Turbo 16/4 Token Ring PC Card 3Com 3C619 TokenLink 3Com 3C319 TokenLink Velocity 3Com 3C389 TokenLink Velocity PC Card SOURCE ROUTING
Setting IFF_LINK0 enables Token-Ring source routing. Setting IFF_LINK1 uses all-routes broadcasts otherwise single-route broadcasts are used. NOTES
The MCA attachment has been only tested on IBM Token Ring 16/4 Adapter/A so far. It doesn't support ifmedia(4) yet, too. SEE ALSO
ifmedia(4), intro(4), isa(4), isapnp(4), mca(4), pcmcia(4), ifconfig(8) HISTORY
The tr driver appeared in NetBSD 1.4. BUGS
The PCMCIA attachment does not work with the cbb(4) CardBus driver. BSD
April 14, 1999 BSD