Sponsored Content
Special Forums IP Networking Multihomed can not ping gateway Post 302285637 by vettec3 on Monday 9th of February 2009 11:14:47 AM
Old 02-09-2009
Hi again.

I loked a bit closer to the ifconfig
eth2 Link encap:Ethernet HWaddr 00:1F:29:5D:B9:89
inet addr:10.18.110.23 Bcast:10.18.110.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Base address:0x5000 Memory:fdde0000-fde00000

And now I see that the interface is up but there is no RUNNING.
I belive that has something to do with my problem.

With mii-tool I can see that the interface nogotiaces a speed and half duplex and so on. But it seems that something could be bad anyway.

Think that I will have to go onsite and check hardware.
 

10 More Discussions You Might Find Interesting

1. IP Networking

Unable to ping the gateway IP itself

We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command 64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies

2. Solaris

ping -s to default gateway very slow

I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies

3. AIX

Can not Ping Gateway

Hello, I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies

4. Red Hat

Cannot ping gateway

I know the subject line is very similar to: destination host unreachable but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there. We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies

5. AIX

IBM Server doesn't ping gateway unless you put a static route

Just want to know if someone has a clue about what could be happening here: I have an AIX box with four NICs in Ether channel connected to a Cisco Switch. When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route. Thanks... (1 Reply)
Discussion started by: witt
1 Replies

6. UNIX for Dummies Questions & Answers

Cannot ping default gateway

I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies

7. AIX

Cant ping default gateway aix 53 07 new install

I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a startsrc -g tcpip ... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies

8. Red Hat

Can not ping default gateway

Hi, Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies

9. AIX

Networking Issue (Cant Ping the gateway)

Hi, I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure? Is there anything that I have to check with vio setting or Am I missing any configuration? Please let me know further. Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies

10. UNIX for Advanced & Expert Users

Unable to ping default gateway

I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos) # ifconfig enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
PBFIFO(8)							       Linux								 PBFIFO(8)

NAME
pfifo - Packet limited First In, First Out queue bfifo - Byte limited First In, First Out queue SYNOPSIS
tc qdisc ... add pfifo [ limit packets ] tc qdisc ... add bfifo [ limit bytes ] DESCRIPTION
The pfifo and bfifo qdiscs are unadorned First In, First Out queues. They are the simplest queues possible and therefore have no overhead. pfifo constrains the queue size as measured in packets. bfifo does so as measured in bytes. Like all non-default qdiscs, they maintain statistics. This might be a reason to prefer pfifo or bfifo over the default. ALGORITHM
A list of packets is maintained, when a packet is enqueued it gets inserted at the tail of a list. When a packet needs to be sent out to the network, it is taken from the head of the list. If the list is too long, no further packets are allowed on. This is called 'tail drop'. PARAMETERS
limit Maximum queue size. Specified in bytes for bfifo, in packets for pfifo. For pfifo, defaults to the interface txqueuelen, as speci- fied with ifconfig(8) or ip(8). The range for this parameter is [0, UINT32_MAX]. For bfifo, it defaults to the txqueuelen multiplied by the interface MTU. The range for this parameter is [0, UINT32_MAX] bytes. Note: The link layer header was considered when counting packets length. OUTPUT
The output of tc -s qdisc ls contains the limit, either in packets or in bytes, and the number of bytes and packets actually sent. An unsent and dropped packet only appears between braces and is not counted as 'Sent'. In this example, the queue length is 100 packets, 45894 bytes were sent over 681 packets. No packets were dropped, and as the pfifo queue does not slow down packets, there were also no overlimits: # tc -s qdisc ls dev eth0 qdisc pfifo 8001: dev eth0 limit 100p Sent 45894 bytes 681 pkts (dropped 0, overlimits 0) If a backlog occurs, this is displayed as well. SEE ALSO
tc(8) AUTHORS
Alexey N. Kuznetsov, <kuznet@ms2.inr.ac.ru> This manpage maintained by bert hubert <ahu@ds9a.nl> iproute2 10 January 2002 PBFIFO(8)
All times are GMT -4. The time now is 07:12 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy