Sponsored Content
Special Forums IP Networking Multihomed can not ping gateway Post 302285311 by vettec3 on Sunday 8th of February 2009 12:13:04 PM
Old 02-08-2009
Ok.

But if dont remember wrong I have the gateway en /etc/sysconfig/network-scripts/ifcfg-ethX
I thought that that was enough ?
 

10 More Discussions You Might Find Interesting

1. IP Networking

Unable to ping the gateway IP itself

We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command 64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies

2. Solaris

ping -s to default gateway very slow

I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies

3. AIX

Can not Ping Gateway

Hello, I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies

4. Red Hat

Cannot ping gateway

I know the subject line is very similar to: destination host unreachable but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there. We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies

5. AIX

IBM Server doesn't ping gateway unless you put a static route

Just want to know if someone has a clue about what could be happening here: I have an AIX box with four NICs in Ether channel connected to a Cisco Switch. When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route. Thanks... (1 Reply)
Discussion started by: witt
1 Replies

6. UNIX for Dummies Questions & Answers

Cannot ping default gateway

I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies

7. AIX

Cant ping default gateway aix 53 07 new install

I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a startsrc -g tcpip ... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies

8. Red Hat

Can not ping default gateway

Hi, Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies

9. AIX

Networking Issue (Cant Ping the gateway)

Hi, I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure? Is there anything that I have to check with vio setting or Am I missing any configuration? Please let me know further. Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies

10. UNIX for Advanced & Expert Users

Unable to ping default gateway

I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos) # ifconfig enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
FORUM(1)							       mrtg								  FORUM(1)

NAME
forum - Interactive Help for MRTG users SYNOPSIS
There is a lot of written documentation for mrtg. But never the less you may have a problem where you can't find the solution. In this case some Human Help may be necessary. With MRTG there are several ways to get Humans to help you. MAILING-LIST There are three mailing lists for MRTG available. mrtg for discussion among mrtg users mrtg-announce for announcements regarding new versions of mrtg related software mrtg-developers for discussion among people who write software in connection with mrtg or who hack mrtg itself. THE RULES Please note, that the memebers of the mrtg mailinglist value politeness highly. This means behave in a way you would like others to behave towards you. o No shouting. (NO CAPS) o No rude language o No demands. everybody is on the list out of their own free will. If you do not get an answer to your question, chances are high that you did not give sufficent details about the nature of your problem or that the answer to your problem is in the documentation. o If you do not follow the rules you will be unsubscribed from the list with no further questions asked. o Decisions about your unsubscription from the list will be taken by Alex van den Bogaerdt <alex@slot.hollandcasino.nl> Paul C. Williamson <pwilliamson@MANDTBANK.COM> If you feel that you have been treated unfairly, you may send mail to me and explain the situation. Tobi Oetiker <oetiker@ee.ethz.ch> SUBSCRIBING These lists are managed by a mailing-list management software (listar). It allows you to subscribe to these lists by sending a message with the subject: subscribe to the following address: listname-request@list.ee.ethz.ch You will then get a message asking you to confirm your subscription. For posting to the lists use the following address listname@list.ee.ethz.ch Note that only people who are subscribed to the list can post. Further information about the usage of the mailing lists is available by sending a message with the subject line help to either one of the request addresses. For past activity there is also a mailing list archive available: http://www.ee.ethz.ch/~slist/mrtg There is also a web interface to manage your mailing-list subscription. http://www.ee.ethz.ch/~slist/lsg2.cgi NEWSGROUP
For discussion of MRTG or related topics on the Usenet, please send your posts to: news:comp.dcom.net-management Many MRTG users are in this forum and will help you. You can also find an archive of past activity from this Newsgroup on: http://www.deja.com/usenet AUTHOR
Tobias Oetiker <oetiker@ee.ethz.ch> and many contributors 3rd Berkeley Distribution 2.9.17 FORUM(1)
All times are GMT -4. The time now is 03:03 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy