02-08-2009
Ok.
But if dont remember wrong I have the gateway en /etc/sysconfig/network-scripts/ifcfg-ethX
I thought that that was enough ?
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
3. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
4. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
5. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
9. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
10. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
LEARN ABOUT DEBIAN
smpppd-ifcfg
SMPPPD-IFCFG(8) SMPPPD SMPPPD-IFCFG(8)
NAME
smpppd-ifcfg - SuSE Meta PPP Daemon
DESCRIPTION
smpppd-ifcfg is a daemon that controls a single dialup connection to the internet. It does so by starting and controlling the pppd. The
configuration of the dialup connections is done by YaST2.
smpppd-ifcfg is not intended for direct use. Use ifup and ifdown or a frontend like cinternet , qinternet or kinternet instead.
OPTIONS
These options are recognized by smpppd-ifcfg. If a long option shows an argument as mandatory, then it is mandatory for the equivalent
short option also.
--up Bring the connection up. This is the default action.
--down Bring the connection down.
--status
Report status of the connection.
-i, --ifcfg=NAME
Specify the ifcfg file to use. This option is mandatory.
-p, --provider=NAME
Specify the provider file to use.
--detach
Detach from the controlling terminal. This is the default.
--nodeatch
Don't detach from the controlling terminal.
-d, --debug
Turn on debugging.
--version
Show program version and exit.
--help Show help information and exit.
FILES
/etc/sysconfig/network/ifcfg-*
Configuration files for the interfaces.
/etc/sysconfig/network/providers/*
Configuration files for the providers.
/var/log/smpppd/ifcfg-xxx.log
Log file.
/var/log/smpppd/accounting.log
File containing accounting information.
/var/run/smpppd.ifcfg-xxx.pid
Pid file.
/var/lib/smpppd/ifcfg-xxx.info
Info file with various status information.
/var/run/smpppd/ifcfg-xxx
Socket to communicate with smpppd.
SEE ALSO
kinternet, qinternet, cinternet(1), accounting(1), wvdial(1), smpppd.conf(5), pppd(8), smpppd(8).
AUTHOR
Arvin Schnell <arvin@suse.de>
SuSE December 2002 SMPPPD-IFCFG(8)