ethernet down Post: 302273963

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Ethernet

We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time...

2. UNIX for Dummies Questions & Answers

Ethernet Initialisation

I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by...

3. Cybersecurity

Ethernet sniff.

I suspect that someone is using a sniffer on my Ethernet connection, OS X 10.3.9, DSL, ok, I'm in terminal using the "ifconfig" command > flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384 right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the...

4. UNIX for Advanced & Expert Users

Virtual Ethernet

I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up?

5. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

6. Solaris

ethernet problem

Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args: SunOS Release 5.8 Version Generic_108528-29 64-bit Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved. ifconfig: plumb: qfe2: Bad file number configuring IPv4 interfaces: eri0. moving addresses...

7. Solaris

ethernet

my solris box network is unreachable how to solve this ipaddress assiagning and entry in vi /etc/host how to solve network is unreachable

8. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter...

9. Linux

ethernet bonding

I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0. Here's what I did: created file /etc/modprobe.d/bonding.d and added the following to it: alias bond0 bonding options bonding...

LEARN ABOUT OPENDARWIN

traceroute6

TRACEROUTE6(8)						    BSD System Manager's Manual 					    TRACEROUTE6(8)

NAME

     traceroute6 -- print the route IPv6 packets will take to the destination

SYNOPSIS

     traceroute6 [-dlnrv] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]

DESCRIPTION

     -d      Debug mode.

     -f firsthop
	     Specify how many hops to skip in trace.

     -g gateway
	     Specify intermediate gateway (traceroute6 uses routing header).

     -m hoplimit
	     Specify maximum hoplimit.

     -l      Print both host hostnames and numeric addresses.  Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
	     addresses if -n is specified.

     -n      Do not resolve numeric address to hostname.

     -p port
	     Set UDP port number to port.

     -q probes
	     Set the number of probe per hop count to probes.

     -r

     -s src  Src specifies the source IPv6 address to be used.

     -v      Be verbose.

     -w waittime
	     Specify the delay time between probes.

RETURN VALUES

     The traceroute6 command will exit with 0 on success, and non-zero on errors.

SEE ALSO

     ping(8), ping6(8), traceroute(8)

HISTORY

     The traceroute6 command first appeared in WIDE hydrangea IPv6 protocol stack kit.

BSD
								   May 17, 1998 							       BSD