01-06-2009
have you tried another nic on the server in the same switch/port/config? you could have a bad nic. also, have you checked w/ your network team on how the switch port is configured?
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time... (5 Replies)
Discussion started by: at_renai2001
5 Replies
2. UNIX for Dummies Questions & Answers
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
Discussion started by: at_renai2001
1 Replies
3. Cybersecurity
I suspect that someone is using a sniffer on my Ethernet connection,
OS X 10.3.9, DSL,
ok, I'm in terminal using the "ifconfig" command >
flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384
right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the... (1 Reply)
Discussion started by: su"do"er
1 Replies
4. UNIX for Advanced & Expert Users
I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Discussion started by: capeme
1 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. Solaris
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies
7. Solaris
my solris box network is unreachable how to solve this
ipaddress assiagning and entry in vi /etc/host
how to solve network is unreachable (2 Replies)
Discussion started by: tirupathi
2 Replies
8. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
RARPD(8) System Manager's Manual RARPD(8)
NAME
rarpd - reverse address resolution protocol daemon
SYNOPSIS
rarpd [-v] [-i interface ]
DESCRIPTION
Rarpd listens on the ethernet for broadcast packets asking for reverse address resolution. These packets are sent by hosts at boot time to
find out their IP address. Rarpd looks up the six octet ethernet number in the ethers map finding a host name. This name is translated to
the IP address of the host by a DNS lookup. The IP address is then sent to the host.
Before rarpd can start its service it first finds out what the IP address and hardware address of the ethernet is.
Warning! Sun diskless workstations assume that the first RARP server that answers is the host they are to boot from. For this to work all
other Sun RARP servers delay their answer if they are not also the requestors boot server. This rarpd does not have this kludge so it will
happily engage the Sun boot server to see who can answer the client first. Unless your host can actually serve a Sun diskless client, it
is better not to list any more hosts in the ethers file than necessary.
OPTIONS
-v Be verbose. Show requests which the daemon is responding to.
-i Bind to the named interface. By default rarpd binds to the default interface for the local system type, if available.
SEE ALSO
ifconfig(8), ethers(5), hosts(5),
AUTHOR
Derrick J. Brashear (shadow@dementia.org)
The man page is mostly from the Minix version, by Kees J. Bot (kjb@cs.vu.nl)
RARPD(8)