Sponsored Content
Operating Systems Solaris Null modem cable in Ultra sparc 10 Post 302271676 by kumarmani on Saturday 27th of December 2008 04:13:39 AM
Old 12-27-2008
To access the system as i am having some prob with my monitor . i was thinking if its support then i can use it through my laptop
 

10 More Discussions You Might Find Interesting

1. IP Networking

unix and the cable modem

If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that... (3 Replies)
Discussion started by: gparsons70
3 Replies

2. UNIX for Dummies Questions & Answers

Linux and my cable modem

I recently installed Caldera 2.4 (successfully:p ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now? (4 Replies)
Discussion started by: zorro
4 Replies

3. UNIX for Dummies Questions & Answers

can't get my cable modem up

Caldera eDesktop 2.4 - Cable Modem my NIC card has been detected, but funny scenario: #dmesg eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef /*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module.... (1 Reply)
Discussion started by: zorro
1 Replies

4. UNIX for Dummies Questions & Answers

Is anyone using unix with cable modem

Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how. Thank you for all your help. (5 Replies)
Discussion started by: gparsons70
5 Replies

5. IP Networking

DHCP Linux and cable modem

I can do all this in windows, but Im trying to run the SuSe 8.0 professional as a gateway. I have the local (private) LAN setup with no problems, but Im having troubles getting it to use DHCP to go out on the external card to the service provider, which only uses Dynamic IP's. WHere, what and how... (3 Replies)
Discussion started by: ftn96
3 Replies

6. UNIX for Dummies Questions & Answers

cable modem to sparc

hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem , i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how... (5 Replies)
Discussion started by: raju
5 Replies

7. BSD

cable modem problem

hi I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system. When I type, I get # ifconfig -a lo0 : .... ... ... rl0 : .... ... ... vr0 : ... ... ... I have two network cards (the machine will be a router). I created... (1 Reply)
Discussion started by: fnoyan
1 Replies

8. Solaris

null modem serial cable for server testing

HI all, i still have a problem when using null modem to see the output from my server(sun ultra en 3000). i followed the instruction from the internet, but it is not working. 1. i am using db9(5 4, 2 rows,put in laptop serial port) and db25(13 12, 2 rows,put in (A) server serial port). 2.... (3 Replies)
Discussion started by: waterbear
3 Replies

9. Solaris

Is the cable you are using a null modem cable or a modem cable

Hi all, Is there any difference between a null modem cable or a modem cable ? i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup. please correct if i am wrong, thks (2 Replies)
Discussion started by: waterbear
2 Replies

10. Hardware

Serial connection CAT5 instead of RS232 and Null Modem or Straight cable.

Hello, I want to connect a VT520 terminal to p3 linux box. I have two questions regarding the connection. First, is it possible to use RJ45 instead of RS232 cable. (with DB9 pin to RJ45 and DB25 to RJ45 converter). Second point is that; do i need null modem cable or straight cable... (5 Replies)
Discussion started by: vectrum
5 Replies
dbus-monitor(1) 					      General Commands Manual						   dbus-monitor(1)

NAME
dbus-monitor - debug probe to print message bus messages SYNOPSIS
dbus-monitor [--system | --session] [--profile | --monitor] [watch expressions] DESCRIPTION
The dbus-monitor command is used to monitor messages going through a D-Bus message bus. See http://www.freedesktop.org/software/dbus/ for more information about the big picture. There are two well-known message buses: the systemwide message bus (installed on many systems as the "messagebus" service) and the per- user-login-session message bus (started each time a user logs in). The --system and --session options direct dbus-monitor to monitor the system or session buses respectively. If neither is specified, dbus-monitor monitors the session bus. dbus-monitor has two different output modes, the 'classic'-style monitoring mode and profiling mode. The profiling format is a compact for- mat with a single line per message and microsecond-resolution timing information. The --profile and --monitor options select the profiling and monitoring output format respectively. If neither is specified, dbus-monitor uses the monitoring output format. In order to get dbus-monitor to see the messages you are interested in, you should specify a set of watch expressions as you would expect to be passed to the dbus_bus_add_watch function. The message bus configuration may keep dbus-monitor from seeing all messages, especially if you run the monitor as a non-root user. OPTIONS
--system Monitor the system message bus. --session Monitor the session message bus. (This is the default.) --profile Use the profiling output format. --monitor Use the monitoring output format. (This is the default.) EXAMPLE
Here is an example of using dbus-monitor to watch for the gnome typing monitor to say things dbus-monitor "type='signal',sender='org.gnome.TypingMonitor',interface='org.gnome.TypingMonitor'" AUTHOR
dbus-monitor was written by Philip Blundell. The profiling output mode was added by Olli Salli. BUGS
Please send bug reports to the D-Bus mailing list or bug tracker, see http://www.freedesktop.org/software/dbus/ dbus-monitor(1)
All times are GMT -4. The time now is 09:01 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy