12-18-2008
Can you try to plumb the interface 1st and then assign the IP and netmask .
# ifconfig hme0 plumb
And then assign the IP
# ifconfig hme0 <ip> netmask <netmask> up
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Solaris
Dear ALL,
my server give me messages like below:
Apr 20 21:33:09 TAISERVER in.routed: interface bge3 to 192.168.11.22 turned off
I check with ifconfig,but nothing error that,how can make it solve...thanks for your help. (7 Replies)
Discussion started by: fredginting
7 Replies
3. IP Networking
Hi,
ifconfig -a return:
eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A
inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0
... (5 Replies)
Discussion started by: djbuly
5 Replies
4. UNIX for Advanced & Expert Users
hi all,
i have problem with my box,
until now i can't investigate the root cause of my issue at my box.
here the problem.
i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Discussion started by: tindasz
1 Replies
5. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
6. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
7. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
8. UNIX for Dummies Questions & Answers
Hi All,
How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
VIRT(4) BSD Kernel Interfaces Manual VIRT(4)
NAME
virt -- rump virtual network interface
SYNOPSIS
#include <rump/rump.h>
int
rump_pub_virtif_create(int num);
DESCRIPTION
The virt interface acts as a link between a rump virtual kernel and a host tap(4) interface. Interface number <n> always corresponds with
the host tap interface tap<n>. All data sent by virt is written into /dev/tap<n> and all data read from /dev/tap<n> is passed as Ethernet
input to the rump virtual kernel.
A virt interface can be created in two ways:
o Programmatically by calling rump_pub_virtif_create().
o Dynamically at runtime with ifconfig(8) or equivalent using the create command.
Destroying a virt interface is possible only through ifconfig(8) destroy.
The host's tap(4) interface can be further bridged with hardware interfaces to provide full Internet access to a rump kernel.
SEE ALSO
rump(3), bridge(4), tap(4), brconfig(8), ifconfig(8)
BSD
November 15, 2010 BSD