12-16-2008
yes..using that metode first convert that 25% free space in to UFS. and later create the Logical particitions in it.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to install Redhat 7.2 on my Windows machine. I only have one hard drive and I dont want to lose Windows. Which method is best for partitioning the HD?
I tried it once with Partition Magic and I was installing Corel Linux First Edition and Corel wiped out my entire HD (not good when... (2 Replies)
Discussion started by: primal
2 Replies
2. UNIX for Dummies Questions & Answers
Hello,
To run UNIX, can the hard disk be partitioned so I could use that part for UNIX and the other for my existing Windows '98? At the moment there are hard drives C: & D:. Also, where can I obtain the UNIX software?.....Your response is appreciated. (2 Replies)
Discussion started by: hpin
2 Replies
3. UNIX for Advanced & Expert Users
Dear Sun gurus,
I have Sun Fire V240 server with its StorEdge 3300 disk-array. Following are its disks appeared in format command. I have prepared its partitions thru format and metainit & metattach (may be i have made wrong steps, causing the errors below because I have done thru some document... (1 Reply)
Discussion started by: shafeeq
1 Replies
4. Shell Programming and Scripting
Hello!
I need to write partitioning script wich would work in rescue mode. It will prepare partitions and unpack linux on it. However I need to calculate whole size of the disk and create:
/dev/sda1 --> One big partition (minus (2*size of memory) for swap)
/dev/sda2 --> Swap partition... (1 Reply)
Discussion started by: pug123
1 Replies
5. Solaris
Hi all
I'm having difficulty setting up a proper disk structure on a 72GB HDD. The drive was previously part of a zfs pool. The zpool has ben destroyed and now I want to use the disk in a raid 5 array. I need to partition the disk accordingly though.
This is what the partition table currently... (7 Replies)
Discussion started by: notreallyhere
7 Replies
6. Red Hat
I'm new to Linux 5, going through initial phases of installation and setting up devices, etc,, and much to my surprise discovered also an existence of a 2nd hard drive to try to initialize and partition perhaps using any built-in command i.e. "fdisk" or similar, but I couldn't get the command to... (4 Replies)
Discussion started by: su
4 Replies
7. Ubuntu
Hi folks,
Ubuntu 10.04-1 64-bit
HD - 1T SATA3
I ran graphic installation installing Ubuntu-10.04-1 desktop from Live CD
The partition on the new HD is as follow;
/root
/home
/kvm
(kvm is for keeping the guests of KVM, the virtualizer)
Installion went through without problem abd... (0 Replies)
Discussion started by: satimis
0 Replies
8. Red Hat
Hi Everyone,
I have added new Virtual disk to OS. The main point is I need to bring this whole Disk into LVM control, is it necessary to partition the disk using fdisk command and assign partition type as '8e', or can I directly add that disk into LVM, by running pvcreate command with out... (2 Replies)
Discussion started by: bobby320
2 Replies
9. UNIX for Dummies Questions & Answers
I m not sure if this is a right question to ask .
During the installation of the OS, installation sw does partitioning for you.
I m not quit sure if they have used parted or fdisk to partition the disk.
(If they are using fdisk then you can't make partition > 2Tb )correct me if i m wrong.Also... (5 Replies)
Discussion started by: pinga123
5 Replies
RK(4) Kernel Interfaces Manual RK(4)
NAME
rk - RK-11/RK03 or RK05 disk
DESCRIPTION
Rk? refers to an entire disk as a single sequentially-addressed file. Its 256-word blocks are numbered 0 to 4871. Minor device numbers
are drive numbers on one controller.
The rk files discussed above access the disk via the system's normal buffering mechanism and may be read and written without regard to
physical disk records. There is also a `raw' interface which provides for direct transmission between the disk and the user's read or
write buffer. A single read or write call results in exactly one I/O operation and therefore raw I/O is considerably more efficient when
many words are transmitted. The names of the raw RK files begin with rrk and end with a number which selects the same disk as the corre-
sponding rk file.
In raw I/O the buffer must begin on a word boundary, and counts should be a multiple of 512 bytes (a disk block). Likewise seek calls
should specify a multiple of 512 bytes.
FILES
/dev/rk?, /dev/rrk?
BUGS
In raw I/O read and write(2) truncate file offsets to 512-byte block boundaries, and write scribbles on the tail of incomplete blocks.
Thus, in programs that are likely to access raw devices, read, write and lseek(2) should always deal in 512-byte multiples.
RK(4)