11-10-2008
Hello.
I've found the solution to my problem. The cable that i build from the schematic has a problem in the transmition pin. I've used a Cisco console cable and now i can transmit commands to the sun.
If anyone is in the same situation try a Cisco cable.
9 More Discussions You Might Find Interesting
1. Solaris
Hello, I'm trying to fix this server System Board (CPU/Memory Unit). The error indicates that its missing 3.3VDC. So far all the fuses and caps have been checked. I new at this type of machine, need help for idea on this system. Thank you in advance.
Vu (0 Replies)
Discussion started by: vhtran
0 Replies
2. What is on Your Mind?
guys - not sure where to post this one but i figured this was the likely spot.
i need a sun dvd slimline for netra t1. hcl matrix has this for production/manufac. number: X7288A / 540-5014.
anyone have a good spot to get this stuff? does anyone have an extra laying around to sell? i hate going... (2 Replies)
Discussion started by: pupp
2 Replies
3. Solaris
Hello,
I wrote a script which monitor the keyswitch state repeatedly each 10 minutes.
I'm extracting the keyswitch status by using prtdiag.
The script works fine for Netra v440 , but I found that prtdiag under Netra 1290 don't give keyswitch status.
unlike Netra 440 server , I found that... (2 Replies)
Discussion started by: Alalush
2 Replies
4. Solaris
Hi guys. I have an old Netra T1 that I'm hoping to recover here so I can twiddle around with Solaris 10.
It's been unable to power on despite issuing the "poweron" command or hitting the switch at the back of the server for some time. The LOM command "env" reports ALARM3 ON and everything else... (8 Replies)
Discussion started by: detach8
8 Replies
5. Solaris
Hi,
When I am trying to boot my SUN Netra 240 Machine its giving some boot error.
> {1} ok boot -i
> Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args: -i
> Boot load failed.
> The file just loaded does not appear to be executable.
> {1} ok
I tried to boot it from cdrom... (9 Replies)
Discussion started by: ppandey21
9 Replies
6. Hardware
As the title suggests, I'm trying to install a second drive (really want an OS mirror) on a Sun Netra X1.
I've taken the spacer out, and had a go at with the drill-press so now I have a nice HDD tray. Have installed an IDE drive in the tray, plugged in the power and data cables that were... (0 Replies)
Discussion started by: Smiling Dragon
0 Replies
7. Hardware
I recently required some Sun Oracle Netra T5220s. I do not have much knowledge of Sun products.
The units do not have video cards or hard drives. How can I tell/go about figuring out what clock speed and how many cores the processor is?
They are all outfitted with 32GB of memory. Two are... (11 Replies)
Discussion started by: nerdboy
11 Replies
8. Solaris
Hello all,
I recently powered on my Netra AX1105 server only to be greeted with the following error message. I am not sure what to do here,
I cant fun fsck on OK prompt.. did ok>boot -r and now it keeps booting from net, then I run ok>boot disk then outputs the following message... and keeps... (3 Replies)
Discussion started by: br1an
3 Replies
9. Solaris
Hi Guys,
Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that?
Thanks! (4 Replies)
Discussion started by: CristianS
4 Replies
LEARN ABOUT OPENDARWIN
liebert
LIEBERT(8) NUT Manual LIEBERT(8)
NAME
liebert - Driver for Liebert contact-closure UPS equipment
NOTE
This man page only documents the hardware-specific features of the liebert driver. For information about the core driver, see nutupsdrv(8).
SUPPORTED HARDWARE
This driver supports some Liebert UPS equipment with a contact-closure interface. This includes the UPStation GXT2 with their
contact-closure cable. The smart mode ("Multilink") cable is not supported by this driver.
EXTRA ARGUMENTS
This driver does not support any extra settings in the ups.conf(5).
BUGS
This driver does not yet support shutdowns by raising DTR. Be aware that shutdowns are not possible with the stock contact-closure cable.
You may have to build another cable with DTR connected through to the UPS for it to work.
There is no way for this driver to detect the hardware or cable. It will start up successfully even if no UPS is present. This is a
fundamental limitation of any contact-closure driver.
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 LIEBERT(8)