Sponsored Content
Full Discussion: please suggest me a site
Top Forums Shell Programming and Scripting please suggest me a site Post 302254934 by danmero on Wednesday 5th of November 2008 01:25:56 PM
Old 11-05-2008
 

10 More Discussions You Might Find Interesting

1. AIX

Look into this and suggest if any changes needed

Hi, I am new script programming, I have written a script shown velow to read username and passwd from /etc/security/passwd, i am able to read username, but unable to grep lastupdate. please look into the code and suggest if any changes need. #!/bin/ksh USERNAME="" fname=/usr/bin/lastupdate... (1 Reply)
Discussion started by: me_haroon
1 Replies

2. Shell Programming and Scripting

Can you suggest a more efficient way for this?

Hi I have the following at the end of a service shutdown script used in part of an active-passive failover setup: ### # Shutdown all primary Network Interfaces # associated with failover ### # get interface names based on IP's # and shut them down to simulate loss of # heartbeatd ... (1 Reply)
Discussion started by: mikie
1 Replies

3. Shell Programming and Scripting

Please suggest some changes in my code

Hi All, I have made the following code which is taking 10-15 mins to execute completely. Here the file am using is very big( around 1050993843). Can any one make some changes in my code which reduces the time it takes to execute as am very much new to Unix(learner). One more thing, i have... (10 Replies)
Discussion started by: madhavsunduru
10 Replies

4. Shell Programming and Scripting

Can yum be used. If not please suggest.

Hi! I need to install a application from one server to several other servers. My script would copy the install-script to other machines and run it.Since it has to be non-interactive , just wondering if yum can be used for the same. Please let me know , if you guys are aware of other... (1 Reply)
Discussion started by: nua7
1 Replies

5. IP Networking

port access to site to site VPN

Setup a site to site VPN between two cisco routers. One of the site locations is unable to access ports such as https://example.com:9001 How do I let them go into port 9001? They can ssh, ftp, telnet and everything else. Is this a VPN issue or ACL access issue? I put permit ip host... (0 Replies)
Discussion started by: photon
0 Replies

6. Shell Programming and Scripting

Any body suggest me.........!!!!

i am jaswanth, i am very new to unix/linux, upto now i worked in windows only., but i took coatching for unix.., and my sir teached all my classes in red hat linux and told me that all are same...!!! I know shall programming in red hat linux.., but now i installed opensloaris but the... (5 Replies)
Discussion started by: strgraphics
5 Replies

7. IP Networking

How to establish site to site vpn - Linux machine and cisco asa?

Hi, I am trying to establish vpn between my linux server and cisco asa at client side. I installed openswan on my cent os. Linux Server eth0 - 182.2.29.10 Gateway - 182.2.29.1 eth1 - 192.9.200.75 I have simple IPtables Like WAN="eth0" LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies

8. IP Networking

Does cisco 1921 router support site to site VPNs using IPSec?

Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? " A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies

9. UNIX for Dummies Questions & Answers

Suggest books

Hi, I'm a beginner and am learning c programming. I want to learn UNIX/LINUX in parallel. But I don't know difference between UNIX and LINUX and where they are applied in real life. As a beginner, some people asked me to start with UNIX. Please let me know some very good books for UNIX. Also a... (6 Replies)
Discussion started by: nerdbee
6 Replies

10. IP Networking

IPSec Openswan Site to Site VPN - Big Pain

Hi @all, I try to connect 2 LANs with IPSec/Openswan LAN 1: 192.168.0.0/24 LAN 2: 192.168.1.0/24 This is my Config: conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
uri_urn(n)					    Tcl Uniform Resource Identifier Management						uri_urn(n)

__________________________________________________________________________________________________________________________________________________

NAME
uri_urn - URI utilities, URN scheme SYNOPSIS
package require Tcl 8.2 package require uri::urn ?1.1.2? uri::urn::quote url uri::urn::unquote url _________________________________________________________________ DESCRIPTION
This package provides two commands to quote and unquote the disallowed characters for url using the urn scheme, registers the scheme with the package uri, and provides internal helpers which will be automatically used by the commands uri::split and uri::join of package uri to handle urls using the urn scheme. COMMANDS
uri::urn::quote url This command quotes the characters disallowed by the urn scheme (per RFC 2141 sec2.2) in the url and returns the modified url as its result. uri::urn::unquote url This commands performs the reverse of ::uri::urn::quote. It takes an urn url, removes the quoting from all disallowed characters, and returns the modified urls as its result. BUGS, IDEAS, FEEDBACK This document, and the package it describes, will undoubtedly contain bugs and other problems. Please report such in the category uri of the Tcllib SF Trackers [http://sourceforge.net/tracker/?group_id=12883]. Please also report any ideas for enhancements you may have for either package and/or documentation. KEYWORDS
rfc 2141, uri, url, urn CATEGORY
Networking uri 1.1.2 uri_urn(n)
All times are GMT -4. The time now is 12:43 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy