10-25-2008
Should be using H/W RAID ?
10 More Discussions You Might Find Interesting
1. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
2. SCO
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies
3. Solaris
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies
4. UNIX for Advanced & Expert Users
I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage.
Would I sacrifice performance if I use the same HBA?
Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies
5. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
6. Solaris
i was given a task which needs to perform a raid 1 on the boot disk, and 4 other disks on raid 10.
Is there any other alternative in installing solaris 10 other than through network installation?will be using solaris update 6.
while reading through the user guide i got pretty confuse.
... (1 Reply)
Discussion started by: monstar1407
1 Replies
7. Solaris
Dear Friends,
I need to configure T5240 with Internal SAS RAID HBA(SG-XPCIESAS-R-INT-Z).. T5240 uses 8 hard disks... From the documents of RAID card I have found that I need to create a jump start server to include three packages SUNWaac, StorMan, SUNWgccruntime if Im using solaris10 5/08...
... (5 Replies)
Discussion started by: nicktrix
5 Replies
8. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
9. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
10. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
MFI(4) BSD Kernel Interfaces Manual MFI(4)
NAME
mfi -- LSI Logic & Dell MegaRAID SAS RAID controller
SYNOPSIS
mfi* at pci? dev ? function ?
DESCRIPTION
The mfi driver provides support for the MegaRAID SAS family of RAID controllers, including:
- Dell PERC 5/e, PERC 5/i, PERC 6/e, PERC 6/i
- Intel RAID Controller SRCSAS18E, SRCSAS144E
- LSI Logic MegaRAID SAS 8208ELP, MegaRAID SAS 8208XLP, MegaRAID SAS 8300XLP, MegaRAID SAS 8308ELP, MegaRAID SAS 8344ELP, MegaRAID
SAS 8408E, MegaRAID SAS 8480E, MegaRAID SAS 8708ELP, MegaRAID SAS 8888ELP, MegaRAID SAS 8880EM2, MegaRAID SAS 9260-8i
- IBM ServeRAID M1015, ServeRAID M5014
These controllers support RAID 0, RAID 1, RAID 5, RAID 6, RAID 10, RAID 50 and RAID 60 using either SAS or SATA II drives.
Although the controllers are actual RAID controllers, the driver makes them look just like SCSI controllers. All RAID configuration is done
through the controllers' BIOSes.
mfi supports monitoring of the logical disks in the controller through the bioctl(8) and envstat(8) commands.
EVENTS
The mfi driver is able to send events to powerd(8) if a logical drive in the controller is not online. The state-changed event will be sent
to the /etc/powerd/scripts/sensor_drive script when such condition happens.
SEE ALSO
intro(4), pci(4), scsi(4), sd(4), bioctl(8), envstat(8), powerd(8)
HISTORY
The mfi driver first appeared in NetBSD 4.0.
BSD
March 22, 2012 BSD