10-22-2008
Pretty sure you'll have to recreate it, since it's a different controller.
RAID 0 or RAID 1?
10 More Discussions You Might Find Interesting
1. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
2. SCO
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies
3. Solaris
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies
4. UNIX for Advanced & Expert Users
I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage.
Would I sacrifice performance if I use the same HBA?
Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies
5. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
6. Solaris
i was given a task which needs to perform a raid 1 on the boot disk, and 4 other disks on raid 10.
Is there any other alternative in installing solaris 10 other than through network installation?will be using solaris update 6.
while reading through the user guide i got pretty confuse.
... (1 Reply)
Discussion started by: monstar1407
1 Replies
7. Solaris
Dear Friends,
I need to configure T5240 with Internal SAS RAID HBA(SG-XPCIESAS-R-INT-Z).. T5240 uses 8 hard disks... From the documents of RAID card I have found that I need to create a jump start server to include three packages SUNWaac, StorMan, SUNWgccruntime if Im using solaris10 5/08...
... (5 Replies)
Discussion started by: nicktrix
5 Replies
8. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
9. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
10. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
LEARN ABOUT NETBSD
ataraid
ATARAID(4) BSD Kernel Interfaces Manual ATARAID(4)
NAME
ataraid -- software BIOS RAID
SYNOPSIS
pseudo-device ataraid
ld* at ataraid? vendtype ? unit ?
DESCRIPTION
The ataraid driver provides support for BIOS-based software RAID controllers. These are devices which have some simple support for several
basic RAID levels (often RAID 0 and RAID 1), but which require software support to actually perform the RAID function. The BIOS support is
largely just to create and recognize the array so that it may be a boot device.
The driver currently supports RAID formats from:
o Adaptec HostRAID (found in Intel 6300ESB)
o Intel MatrixRAID
o JMicron RAID
o nVidia MediaShield
o Promise FastTrak
o Via V-RAID (found in many VIA-based motherboards)
Status of the logical disk as well as the disks associated with it, can be viewed through the bioctl(8) utility.
SEE ALSO
ld(4), bioctl(8)
HISTORY
The ataraid driver first appeared in NetBSD 2.0.
AUTHORS
The ataraid driver was originally adapted from FreeBSD by Jason Thorpe <thorpej@NetBSD.org>.
BUGS
Not all features of the software RAID are currently recognized or supported. For example, the Adaptec support doesn't recognize when a RAID
1 should be in a ``building'' state, and it does not do the right thing.
At least part of the reason for this is that the publically-available information on these formats is quite limited.
BSD
September 16, 2008 BSD