09-23-2008
any seven segment....serial port
could i using minicom to communicate with seven segment?
10 More Discussions You Might Find Interesting
1. Programming
When run it, segment fault.
What is wrong?
#include <stdio.h>
#include <stdlib.h>
const int max =20;
//****************************************************
// Input Matrix
//****************************************************
void inMatrixAA(int *AA, int row, int col)... (9 Replies)
Discussion started by: zhshqzyc
9 Replies
2. Shell Programming and Scripting
Hey all, could someone please direct me on how to extract a segment from a file between two tags? Thanks! (1 Reply)
Discussion started by: mpang_
1 Replies
3. UNIX for Dummies Questions & Answers
how do i close a do code segment? od? (1 Reply)
Discussion started by: trob
1 Replies
4. Solaris
Hi,
I have freshly installed solaris 10 update 5 on my desktop, and during the installation, I specified a static IP address, gateway, netmask.
When I run "ifconfig rtls0" after the installation, I get the following message
#ifconfig rtls0
rtls0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4>... (8 Replies)
Discussion started by: krishisthere
8 Replies
5. Programming
I mean, I malloc a segment of memory, maybe 1k maybe 20bytes.. assume the pointer is pMem How can I know the content pMem refered is all Zero or \0 . I know memcmp but the second parameter should another memory address... thanx (4 Replies)
Discussion started by: macroideal
4 Replies
6. Programming
Hi to all.
I'm reciving a "Segment violation" error from this code and I don't know why.
void insertAtEnd(NodeType *pList) {
char element;
printf("Introduce a element: \n");
setbuf(stdin, NULL);
scanf("%c", &element);
//Find the end of the list;
while... (4 Replies)
Discussion started by: daniel.gbaena
4 Replies
7. Programming
Hi,
Whether the following piece of code is placed in the read-only memory of code (text) segment or data segment?
char *a = "Hello";
I am getting two different answers while searching in google :( that's why the confusion is (7 Replies)
Discussion started by: royalibrahim
7 Replies
8. Solaris
Can anyone please explain what does these means ?
# dladm show-dev
nxge0 link: up speed: 1000 Mbps duplex: full
nxge1 link: up speed: 1000 Mbps duplex: full
e1000g0 link: up speed: 1000 Mbps duplex: full
e1000g1 ... (6 Replies)
Discussion started by: dehetoxic
6 Replies
9. Programming
I always get segment fault, why? can sb help me and modify it, I have spend on much time on
#include <pthread.h>
#include <stdio.h>
#include <stdlib.h>
#include <sys/time.h>
#include <string.h>
#define MAX 10
pthread_t thread;
void *thread1()
{
int *a;
int i, n;
... (1 Reply)
Discussion started by: yanglei_fage
1 Replies
10. Red Hat
Hi all,
I'm running Red Hat Enterprise Linux Server 6.3 Santiago.
I already installed the X Window package during installation and the graphical login display can be shown normally after installation.
Yesterday, I accessed remotely by GUI mode using VNC viewer and somehow it got crashed.... (1 Reply)
Discussion started by: sergionicosta
1 Replies
GRE(4) BSD Kernel Interfaces Manual GRE(4)
NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO
gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD
November 7, 2014 BSD