09-17-2008
Tape Drive
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How will i check the tape drive is availaple are not.
Thanks in advance.
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm trying to install a tape drive on a compaq SCO OS 505. well I have gone through the mkdev tape comands and what have you yet no luck. when I reboot and do a simple tape rewind it gives me an error no such device etc.etc. IS there a diference in the xct0 and rct0 a the default?
help.. (2 Replies)
Discussion started by: kikkin
2 Replies
2. Linux
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Discussion started by: RuralTurtle
0 Replies
3. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
4. SCO
Dear All,
I have a tape drive which has worked for offer 3yrs properly on SCO Openserver Release = 3.2v5.0.5. I tried to clean it all invain. I did a fresh installation of unix of the same OS and did the configuration still didn't bear fruits. The tape is a scsi and the configuration is as... (4 Replies)
Discussion started by: njoroge
4 Replies
5. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
6. SCO
I've recently been tasked with "refurbishing" an HP Proliant ML370 running SCO 5.0...something. This is primarily used for legacy support and is kept on a shelf for safe keeping. The scope of work includes hardware diagnostics and blowing the dust out.
I have run HP diagnostics on the array,... (1 Reply)
Discussion started by: v1corp
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
Discussion started by: samnyc
1 Replies
8. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
LEARN ABOUT CENTOS
amtape
AMTAPE(8) System Administration Commands AMTAPE(8)
NAME
amtape - Control Amanda changers
SYNOPSIS
amtape [-o configoption...] config subcommand [subcommand_options...]
DESCRIPTION
Amtape is the command-line interface to Amanda's tape changers (amanda-changers(7)) and to the taperscan algorithm (amanda-taperscan(7)).
Tape changers maintain a notion of the current slot for each configuration. This may or may not correspond to an actual physical state of
the device, but is used by some taperscan algorithms to minimize searching through the slots.
Amtape uses the default changer. To use a different changer, use the config override option, e.g., -otpchanger=otherchanger.
SUBCOMMANDS
label label
Search for and load the Amanda tape with label [label], also setting the current slot.
slot slot
Load the volume in the given slot, also setting the current slot. The slot names current, next, first, and last have special meaning.
current
Shorthand for slot current.
inventory
Show the contents of all slots, based on the changer's cached metadata. This is a quick operation as it does not load or unload any
volumes, but is not supported by all changers.
show [slots]
Show the contents of all slots (or listed slots) by loading each slot and reading its label. This can be very slow. The slots arguments
is of the form 1,3-5,7.
reset
Reset the changer to a known state. This subcommand is intended to clear any unknown and potentially incorrect state the changer may
have stored.
eject [drive]
Eject the tape currently in the drive. This only applies to some changers. Specify a drive (by drive number) if more than one drive is
available.
clean [drive]
If a cleaning tape is defined for the changer, used it to clean the specified drive. The [drive] is optional if the changer only has
one drive.
taper
Run the taperscan algorithm (see amanda-taperscan(7)), displaying information about the progress of the scan.
update [what]
Update changer state. Consult amanda-changers(7) for changer-specific details on the format of what.
-o configoption
See the "CONFIGURATION OVERRIDE" section in amanda(8).
SEE ALSO
amanda(8), amanda-changers(7), amanda-taperscan(7), amanda-devices(7)
The Amanda Wiki: : http://wiki.zmanda.com/
AUTHORS
Dustin J. Mitchell <dustin@zmanda.com>
Zmanda, Inc. (http://www.zmanda.com)
James da Silva <jds@amanda.org>
Stefan G. Weichinger <sgw@amanda.org>
Amanda 3.3.3 01/10/2013 AMTAPE(8)