08-06-2008
Storedge D1000 sharing disks between two boxes
Hello,
I have a d1000, it's connected to two servers, I want both servers to see all disks in the array. i.e. i have 6 disks, 3 in each side, I want both servers to see all 6 disks.
It appears to be setup in a split bus mode now, ive looked thru the manuals and have become confused!
So, other than trying all the dip switch combinations manually, i wonder if anyone knows how to set the d1000 up in this manner.
Thanks if anyone can help!
B
10 More Discussions You Might Find Interesting
1. Programming
Hi !
Please tell me how to get radio buttons, text boxes , check boxes , option buttons , pull down menus in C++ on Unix.
I think it would be done using curses.h ..but that's all i know.
TIA,
Devyani. (3 Replies)
Discussion started by: devy8
3 Replies
2. UNIX for Advanced & Expert Users
Hi,
I have an application which must use a unified database, the application will run on 4 SCO boxes, so the database will be in one of them and the application in the other 3 servers will access this database on the host machine. This is as a file sharing application in windows. I know this... (0 Replies)
Discussion started by: BAM
0 Replies
3. IP Networking
I have RedHat 9.0 installed on three of my servers (PIII - 233MHz) and want that they share a common IP address so that any request made reaches each of the servers.
Can anyone suggest how should I setup my LAN. I'm new to networking in Linux so please elaborate and would be thankful for a timely... (2 Replies)
Discussion started by: Rakesh Ranjan
2 Replies
4. Solaris
Hi folks,
I´m having a problem with a Ultra60 box with diff scsi pci card
conected to one D1000. The conection are correct because a checked the
D1000 guide. When a do probe-scsi-all in the OBP, the D1000 blink all
disks one time then the led of one of the disks powers off and then
nothing... (2 Replies)
Discussion started by: spacewalker
2 Replies
5. Solaris
Sorry if this seems trivial. i have been given a task at work to configure a sun processing server "enterprise 4500" so it can work with the a storage server "storedge A5200" and "storedge D1000"
the truth is i have never worked on a sun server before. i need a guideline (step by step) as to... (5 Replies)
Discussion started by: lawalidowu
5 Replies
6. UNIX for Advanced & Expert Users
Hi All,
Is there anyway two nodes can share D1000 or minipack with 6 disk slots.
Right now I have minipacks and I am connecting to Sunblade 100 and Sunbladew 150 separately. I would like to connect two systems to one minipack and able see the all the disks on both systems.
I do have D1000... (0 Replies)
Discussion started by: sriny
0 Replies
7. Solaris
Hi Community,
could you provide me a procedure or solaris 10 tool/command or Veritas command to check ths Storedge IP?
Thank you!!! (4 Replies)
Discussion started by: Sunb3
4 Replies
8. Solaris
Hi,
Recently i was trying to connect Sun Storedge D1000 Array to E420 R (Practice servers). I connected the SCSI cable between array and server. I tried the following :
#devfsadm (nothing showed up)
#format (no new disk is shown here)
i tried this process again after putting ON the... (2 Replies)
Discussion started by: bluegold86
2 Replies
9. Solaris
Hi.
I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID.
Essentially, the quesion is, how can this be done? :confused:
I checked... (5 Replies)
Discussion started by: alexs77
5 Replies
10. Solaris
I am trying to connect D1000 storedge with my sun blade 1500 and i am getting the following error when booting the system.
Oct 13 22:21:56 brampton rpcbind: rpcbind terminating on signal.
Oct 13 22:22:02 brampton syseventd: SIGHUP caught - reloading modules
Oct 13 22:22:02 brampton... (9 Replies)
Discussion started by: mnathan
9 Replies
LEARN ABOUT SUSE
vgreduce
VGREDUCE(8) System Manager's Manual VGREDUCE(8)
NAME
vgreduce - reduce a volume group
SYNOPSIS
vgreduce [-a|--all] [-A|--autobackup y|n] [-d|--debug] [-h|-?|--help] [--removemissing] [-t|--test] [-v|--verbose] VolumeGroupName [Physi-
calVolumePath...]
DESCRIPTION
vgreduce allows you to remove one or more unused physical volumes from a volume group.
OPTIONS
See lvm for common options.
-a, --all
Removes all empty physical volumes if none are given on command line.
--removemissing
Removes all missing physical volumes from the volume group, if there are no logical volumes allocated on those. This resumes normal
operation of the volume group (new logical volumes may again be created, changed and so on).
If this is not possible (there are logical volumes referencing the missing physical volumes) and you cannot or do not want to remove
them manually, you can run this option with --force to have vgreduce remove any partial LVs.
Any logical volumes and dependent snapshots that were partly on the missing disks get removed completely. This includes those parts
that lie on disks that are still present.
If your logical volumes spanned several disks including the ones that are lost, you might want to try to salvage data first by acti-
vating your logical volumes with --partial as described in lvm (8).
SEE ALSO
lvm(8), vgextend(8)
Sistina Software UK LVM TOOLS 2.02.67(2) (2010-06-04) VGREDUCE(8)