07-05-2008
Thanks for your replay.
I dont have any disk group and SAN. I am using Intel P3-1GHz,512 and two Hard disks (40gb and 20gb). In 40gb i have installed Solaris 10(2005) and Storage Foundation's Veritas Volume Manager 5.0. 20gb hard disk is empty. How can i bring 20gb into cds format.?
8 More Discussions You Might Find Interesting
1. IP Networking
I have Linux 7.1 setup on a Dell and am unable to bring up any interfaces. Both the lo and eth0 fail upon boot up and I get a insmod error possibly due to bad irq or IO setting.
If I disable eth0 upon boot, then lo works fine, but offcourse I get the "delaying initialization" upon boot for eth0... (1 Reply)
Discussion started by: alam
1 Replies
2. UNIX for Dummies Questions & Answers
The last thing I did was set REMOTE_LOGIN_PASSWORDFILE to EXCLUSIVE. Then rebooted server. Since that time I have not been able to login. During bootup it can't find root and generates alot of errors. Does anybody know of a default login and password that will allow me to log in and rebuild the... (2 Replies)
Discussion started by: mayewil
2 Replies
3. Red Hat
Hello,
I have few HDD and SSD installed in my RHEL 5 server. I want to know which disk are SDD and which are HDD. What command should I use?
Thanks (3 Replies)
Discussion started by: fahdmirza
3 Replies
4. Linux
Hi Guys,
I want to bring my server live.
I have Static public IP Address 123.99.88.77 (Say) and also I have also registered a domain name say(live server23.com) the domain name providers have also given me the control panel with DNS management settings.
I have gateway 192.168.1.1
Now My... (1 Reply)
Discussion started by: manalisharmabe
1 Replies
5. Solaris
:confused:
when i tried to look the status of DNS-client, it is in maintenance mode.....
Please tell me how to bring it back to online mode...PLEASE TELL ME STEP BY STEP.... PLEASE...
:wall: (2 Replies)
Discussion started by: vamshigvk475
2 Replies
6. Solaris
this is samiulla
in my vmware solaris 11 i installed iscsitgt pakage but it goes to maintenance
and i am unable to bring into online with svcadm clear iscsitgt
how can i forcefully online iscsitgt service. (1 Reply)
Discussion started by: samiulla
1 Replies
7. Shell Programming and Scripting
Hi Experts,
Problem summary :
I am facing the below problem on huge files when the disk is getting full on the half way through the execution.
If the disk was already full , the commands fail & everything is fine.
Sample Code :
head_rec_data_file=`head -1 sample_file.txt`
cat... (9 Replies)
Discussion started by: Pruthviraj_shiv
9 Replies
8. AIX
Hi all, I have the following in hacmp.out for bringing Resource group online.
Volume groups themselves are Enhanced-Capable and on each node I can varyon and mount filesystems.
+main1_rg_01:cl_activate_vgs STATUS=0
+main1_rg_01:cl_activate_vgs typeset -li STATUS
+main1_rg_01:cl_activate_vgs... (2 Replies)
Discussion started by: OdilPVC
2 Replies
LEARN ABOUT CENTOS
applydeltarpm
APPLYDELTARPM(8) System Manager's Manual APPLYDELTARPM(8)
NAME
applydeltarpm - reconstruct an rpm from a deltarpm
SYNOPSIS
applydeltarpm [-v] [-p] [-r oldrpm] deltarpm newrpm
applydeltarpm -c|-C deltarpm
applydeltarpm [-c|-C] -s sequence
applydeltarpm -i deltarpm
DESCRIPTION
applydeltarpm applies a binary delta to either an old rpm or to on-disk data to re-create a new rpm. The old rpm can be specified with the
-r option, if no rpm name is provided on-disk data is used. You can use -p to make applydeltarpm print the percentage of completion, or -v
to make it more verbose about its operation.
The second an third form can be used to check if the reconstruction is possible. It may fail if the on-disk data got changed (deltarpms are
created in a way that config file changes do not matter) or the deltarpm does not match the rpm the delta was generated with. The -c option
selects full (i.e. slow) on-disk checking, whereas -C only checks if the filesizes have not changed.
Instead of a full deltarpm a sequence id can be given with the -s sequence option. Such an id contains all the information that is needed
to do reconstruction checking.
Finally information about a deltarpm can be printed with the -i option.
MEMORY CONSIDERATIONS
applydeltarpm was written to work on systems with limited memory. It uses a paging algorithm to keep the size of in-core data low and not
bring the system in an out-of-memory situation.
EXIT STATUS
applydeltarpm returns 0 if the rpm could be recreated or the checking succeeded, it returns 1 and prints an error message to stderr if
something failed.
SEE ALSO
makedeltarpm(8), rpm(8)
AUTHOR
Michael Schroeder <mls@suse.de>
Feb 2005 APPLYDELTARPM(8)