Eth1 turn off by itself after reboot Post: 302191237

10 More Discussions You Might Find Interesting

1. Solaris

different between soft reboot and hard reboot

Hi Guru's Can any want here could explain to me the different between soft reboot and hard reboot . Best Regards Seelan

2. UNIX for Dummies Questions & Answers

/etc/rc.d/net - eth1

I just installed Crux on my laptop, which means I'll have to configure /etc/rc.d/net to adapt to my wireless internet. When I ran Linux before, I connected through eth1. How should I configure the /etc/rc.d/net file accordingly? Thanks for reading, Octal.

3. Red Hat

ifcfg-eth0 and eth1 is N/A

when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in /etc/sysconfig/network-scripts/. what will i do?

4. Solaris

Reg- eth0,eth1 (ethernet card)

Hi Guys, I am working as a L-1 support and i want to know that are the precaution need to take on eth0(Ethernet card) i heard on production server it is very much important, what are the steps need to observe on this tickets.

5. IP Networking

assign mac address for virtual interface eth1:0

Hi , by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces. would some one help me out in this. Thanks Gopi

6. UNIX for Dummies Questions & Answers

Removing IP address from eth1 on SUSE

Hello folks; I have a NIC card on my SUSE 10.3 server with eth0 & eth1 configured with two IP addresses (172.16.5.3 & 172.16.5.4) I'd like to remove the IP assigned to eth1 (172.16.5.4). i think i know i can go into ifcfg-eth1 and edit it but before i do that, i want to know if there's a better...

7. UNIX for Advanced & Expert Users

Multihomed server, eth1 not working

Hey everyone. We're in the process of deploying a number of servers. They're HP DL360 G6's. OS is RHEL 5.4 They've got two on board NIC's, as well as an additional dual port network card, giving us a total of 4 NIC's. Eth0 and Eth2 are bonded together using the bonding module, and the resulting...

8. IP Networking

Problem in eth0 and eth1 sharing internet with other computers

hellow everbody. iam using 32 bit centos 6.2 on my desktop and iam new to linux. i have eth0 and eth1 on my desktop. so i have some problems i have menson here: i have edited: etc/sysctl.conf net.ipv4.ip_forward = 1 and i have edited iptables too # iptables -t nat -A...

9. Red Hat

Wan on eth1 and Lan on eth0

I have a local network on dev eth0 Server has static IP of 10.0.0.1 Gateway is 10.0.0.1 and Dns is 10.0.0.1 I am using this network for imaging 500 plus computer... Now, Issue that I am having is that I need to update packages and I dont want to change the configuration on eth0 because I...

10. Red Hat

Dual NICs - When I 'ifup eth1' it replaces eth0

I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1. I can execute ifup eth0 and bring the interface up quite happily, however when I execute ifup eth1 it...

LEARN ABOUT MINIX

reboot

REBOOT(8)						      System Manager's Manual							 REBOOT(8)

NAME

       reboot - reboot the system immediately

SYNOPSIS

       reboot [-f]

DESCRIPTION

       Reboot  can  be	used  to  reboot  the  system  after  installing a new kernel.	It does not inform the users, but does log it's actions in
       /usr/adm/wtmp and /usr/adm/authlog.  The system is then rebooted with the reboot(2) systemcall.

       If the -f flag is not given then all processes are sent terminate signals to give them a chance to die peacefully before the reboot() call.

       If the wtmp file exists, reboot logs itself as if it were a shutdown.  This is done to prevent last(1) from talking  about  system-crashes.
       Reboot is registered as is in the authlog file.

       Reboot can only be executed by the super-user.  Any other caller will be refused, either by reboot(8) or by reboot(2).

SEE ALSO

       reboot(2), shutdown(8), halt(8), boot(8).

BUGS

       The  error message's given by reboot are not always useful.  There are several routines that can fail, but which are not fatal for the pro-
       gram.

AUTHOR

       Edvard Tuinder (v892231@si.hhs.NL)

																	 REBOOT(8)

10 More Discussions You Might Find Interesting

1. Solaris

different between soft reboot and hard reboot

Discussion started by: seelan3

2. UNIX for Dummies Questions & Answers

/etc/rc.d/net - eth1

Discussion started by: Octal

3. Red Hat

ifcfg-eth0 and eth1 is N/A

Discussion started by: kenshinhimura

4. Solaris

Reg- eth0,eth1 (ethernet card)

Discussion started by: kurva