Sponsored Content
Full Discussion: interface may off
Operating Systems Solaris interface may off Post 302187594 by pupp on Monday 21st of April 2008 01:44:29 PM
Old 04-21-2008
is bge3 going to a switch or router?
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. Solaris

no such interface

Hi Community, I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output: # ifconfig hme0 <ip_address> netmask <mask> plumb #ifconfig: plumb: hme0: no such interface I've the same thing with dhcp service. could you provide any solution... (1 Reply)
Discussion started by: Sunb3
1 Replies

3. IP Networking

How to down interface without name

Hi, ifconfig -a return: eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0 ... (5 Replies)
Discussion started by: djbuly
5 Replies

4. UNIX for Advanced & Expert Users

interface problem

hi all, i have problem with my box, until now i can't investigate the root cause of my issue at my box. here the problem. i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Discussion started by: tindasz
1 Replies

5. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

6. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

7. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

8. UNIX for Dummies Questions & Answers

Interface

Hi All, How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
Router::Simple::Cookbook(3pm)				User Contributed Perl Documentation			     Router::Simple::Cookbook(3pm)

NAME
Router::Simple::Cookbook - The Router::Simple Cookbook FAQ
How to create Sinatra-ish framework with Router::Simple? Please read the following example code. package MySinatraish; use Router::Simple; use Plack::Request; sub import { my $pkg = caller(0); my $router = Router::Simple->new(); my $any = sub ($$;$) { my ($pattern, $dest, $opt) = do { if (@_ == 3) { my ($methods, $pattern, $code) = @_; ($pattern, {code => $code}, +{method => [ map { uc $_ } @$methods ]}); } else { my ($pattern, $code) = @_; ($pattern, {code => $code}, +{}); } }; $router->connect( $pattern, $dest, $opt, ); }; no strict 'refs'; # any [qw/get post delete/] => '/bye' => sub { ... }; # any '/bye' => sub { ... }; *{"${pkg}::any"} = $any; *{"${pkg}::get"} = sub { $any->([qw/GET HEAD/], $_[0], $_[1]); }; *{"${pkg}::post"} = sub { $any->([qw/POST/], $_[0], $_[1]); }; *{"${pkg}::as_psgi_app"} = sub { return sub { if (my $p = $router->match($_[0])) { [200, [], [$p->{code}->()]]; } else { [404, [], ['not found']]; } } }; } package MyApp; use MySinatraish; get '/' => sub { 'top'; }; post '/new' => sub { 'posted'; }; as_psgi_app; How to switch from HTTPx::Dispatcher? HTTPx::Dispatcher is class specific declararative router. package MyApp::Dispatcher; use HTTPx::Dspatcher; connect '/', {controller => 'foo', action => 'bar'}; 1; The following script is same as above. package MyApp::Dispatcher; use Router::Simple::Declare; my $router = router { connect '/', {controller => 'foo', action => 'bar'}; }; sub match { $router->match() } How to use Router::Simple with non-strictly-MVC application? use Router::Simple::Declare; my $router = router { connect '/foo/bar/' => { 'target' => '/foobar.asp' }; connect '/topics/:topic' => { target => '/my-topic.asp' }; connect '/products/{Category:.*}' => { target => '/products.asp', Category => 'All' }; connect '/zipcode/{zip:[0-9]{5,5}}' => {target => '/zipcode.asp' }; }; You can pass the target path as destination. AUTHOR
Tokuhiro Matsuno <tokuhirom AAJKLFJEF GMAIL COM> LICENSE
Copyright (C) Tokuhiro Matsuno This library is free software; you can redistribute it and/or modify it under the same terms as Perl itself. SEE ALSO
Router::Simple perl v5.14.2 2011-05-15 Router::Simple::Cookbook(3pm)
All times are GMT -4. The time now is 01:09 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy