02-16-2008
Is it your intent to merely have these 2 machines connect, or to set 2 routes?
If your intent is to have both machines connect, then just put them both on 192.168.1 . Your home "router" shouldn't care if the connection is stiatc or dynamic - some of them may require you set an IP range that dhcp can serve - so just set the bge0 interface to 192.168.1.4 (or whatever you want the last octet to be).
If your intent is to, well I don't know how our specific home router works and if it lets you create vlans or just point to other devices, but the network would be 10.10.10.0, the mask 255.255.255.0; as for the gateway IP, again, I don't know how your specific home device works, usually you'll enter the gateway IP address of another switch(or vlan in the switch) ; I'd try to enter 10.10.10.2, the IP address of the Sun desktop, and see if it works.
But it'd just be easier to set a range of DHCP addresses in your home device and hardcode a 192.168.1 address on the Sun desktop.
10 More Discussions You Might Find Interesting
1. IP Networking
I am running Mandrake 8.0 (KDE ver 2.1.1) on a machine with 2 NICs. This is a college project. I am attempting to configure this machine as a firewall, and to pass packets from one network to another. Eth0 is on my external network. Eth1 is on my internal network. I set the gateway in "netconf"... (1 Reply)
Discussion started by: Deuce
1 Replies
2. HP-UX
Hi
I'm new about UNIX, but I've to use a HP9000 with HP-UX 10.20 workstation. I'm trying to configure the network, I've configured the file /etc/rc.conf.d/netconf with my IP address and the right gateway, so the HP9000 is on the net, I've tried a ping. But now I've a problem I can't start hte CDE,... (4 Replies)
Discussion started by: gofmass
4 Replies
3. Solaris
i have a router from my isp provider 02. my internet works fine in windows but i am unable to use internet in solaris. when i tried ifconfig command
i was able to see the lo0 which is my laoopback adapter. pls can someone advice. (7 Replies)
Discussion started by: seyiisq
7 Replies
4. Solaris
Hi all
I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem.
So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
Discussion started by: sbk1972
2 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. IP Networking
Hi,
I would like to ask some networking solution regarding my work LAN and 3G usb network problem. I want to route my internet traffic to the 3G network and sometimes connect to some of my work network for ssh to configure some workstation or print something. Currently my problem is i can't... (0 Replies)
Discussion started by: jao_madn
0 Replies
7. IP Networking
hi, I've wrote my own network routing algorithm in java, now i wanna test it and see if it works correctly, also i wanna test it's performance in comparison with other network routing algorithms like RIP. can anyone tell me how can i do this? is there any simulator or something for network routing... (0 Replies)
Discussion started by: gongotar
0 Replies
8. Web Development
Hi
from Running web apps from your home folder
I've more or less follow the guide,
the reason why I'm expering 403 Forbidden is because the higher level directory will take precedance.
$ ls -lrthd /home/phpmy/www/joomla/ drwxrwxr-x 2 phpmy phpmy 4.0K May 1 20:26... (2 Replies)
Discussion started by: jediwannabe
2 Replies
9. IP Networking
Hello,
I'm attempting to setup a test network with a client-server based architecture using a proprietary application. The client works by communicating with the server on separate links (typically cellular connections) and then initiates a tunnel over each active link. However, in place of the... (0 Replies)
Discussion started by: shadyuk
0 Replies
10. Solaris
hi,
not an expert in Solaris networking so would like to ask your opinions
Say i want to configure packet routing from source 10.126.120.130 (A) to destination 10.214.140.9 (B).
I configured it this way (shown in netstat -rn) on (B)
Destination Gateway Interface... (7 Replies)
Discussion started by: ghostdog74
7 Replies
LEARN ABOUT FREEBSD
if_gre
GRE(4) BSD Kernel Interfaces Manual GRE(4)
NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO
gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD
November 7, 2014 BSD