02-16-2008
Is it your intent to merely have these 2 machines connect, or to set 2 routes?
If your intent is to have both machines connect, then just put them both on 192.168.1 . Your home "router" shouldn't care if the connection is stiatc or dynamic - some of them may require you set an IP range that dhcp can serve - so just set the bge0 interface to 192.168.1.4 (or whatever you want the last octet to be).
If your intent is to, well I don't know how our specific home router works and if it lets you create vlans or just point to other devices, but the network would be 10.10.10.0, the mask 255.255.255.0; as for the gateway IP, again, I don't know how your specific home device works, usually you'll enter the gateway IP address of another switch(or vlan in the switch) ; I'd try to enter 10.10.10.2, the IP address of the Sun desktop, and see if it works.
But it'd just be easier to set a range of DHCP addresses in your home device and hardcode a 192.168.1 address on the Sun desktop.
10 More Discussions You Might Find Interesting
1. IP Networking
I am running Mandrake 8.0 (KDE ver 2.1.1) on a machine with 2 NICs. This is a college project. I am attempting to configure this machine as a firewall, and to pass packets from one network to another. Eth0 is on my external network. Eth1 is on my internal network. I set the gateway in "netconf"... (1 Reply)
Discussion started by: Deuce
1 Replies
2. HP-UX
Hi
I'm new about UNIX, but I've to use a HP9000 with HP-UX 10.20 workstation. I'm trying to configure the network, I've configured the file /etc/rc.conf.d/netconf with my IP address and the right gateway, so the HP9000 is on the net, I've tried a ping. But now I've a problem I can't start hte CDE,... (4 Replies)
Discussion started by: gofmass
4 Replies
3. Solaris
i have a router from my isp provider 02. my internet works fine in windows but i am unable to use internet in solaris. when i tried ifconfig command
i was able to see the lo0 which is my laoopback adapter. pls can someone advice. (7 Replies)
Discussion started by: seyiisq
7 Replies
4. Solaris
Hi all
I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem.
So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
Discussion started by: sbk1972
2 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. IP Networking
Hi,
I would like to ask some networking solution regarding my work LAN and 3G usb network problem. I want to route my internet traffic to the 3G network and sometimes connect to some of my work network for ssh to configure some workstation or print something. Currently my problem is i can't... (0 Replies)
Discussion started by: jao_madn
0 Replies
7. IP Networking
hi, I've wrote my own network routing algorithm in java, now i wanna test it and see if it works correctly, also i wanna test it's performance in comparison with other network routing algorithms like RIP. can anyone tell me how can i do this? is there any simulator or something for network routing... (0 Replies)
Discussion started by: gongotar
0 Replies
8. Web Development
Hi
from Running web apps from your home folder
I've more or less follow the guide,
the reason why I'm expering 403 Forbidden is because the higher level directory will take precedance.
$ ls -lrthd /home/phpmy/www/joomla/ drwxrwxr-x 2 phpmy phpmy 4.0K May 1 20:26... (2 Replies)
Discussion started by: jediwannabe
2 Replies
9. IP Networking
Hello,
I'm attempting to setup a test network with a client-server based architecture using a proprietary application. The client works by communicating with the server on separate links (typically cellular connections) and then initiates a tunnel over each active link. However, in place of the... (0 Replies)
Discussion started by: shadyuk
0 Replies
10. Solaris
hi,
not an expert in Solaris networking so would like to ask your opinions
Say i want to configure packet routing from source 10.126.120.130 (A) to destination 10.214.140.9 (B).
I configured it this way (shown in netstat -rn) on (B)
Destination Gateway Interface... (7 Replies)
Discussion started by: ghostdog74
7 Replies
PRIPS(1) BSD General Commands Manual PRIPS(1)
NAME
prips -- print the IP addresses in a given range
SYNOPSIS
prips [-c] [-d delim] [-e exclude] [-f format] [-i incr] start end
prips [-c] [-d delim] [-e exclude] [-f format] [-i incr] CIDR-block
prips -h
DESCRIPTION
The prips tool can be used to print all of the IP addresses in a given range. It can enhance tools that only work on one host at a time,
e.g. whois(1).
The prips tool accepts the following command-line options:
-c Print the range in CIDR notation.
-d delim
Set the delimiter to the character with ASCII code delim where 0 <= delim <= 255.
-e <x.x.x,x.x>
Exclude ranges from the output.
-f format
Set the format of addresses (hex, dec, or dot).
-h Show summary of options.
-i incr
Set the increment to 'x'.
ENVIRONMENT
The prips tool's operation is not influenced by any environment variables.
FILES
The prips tool's operation is not influenced by any files.
EXAMPLES
Display all the addresses in a reserved subnet:
prips 192.168.32.0 192.168.32.255
The same, using CIDR notation:
prips 192.168.32/24
Display only the usable addresses in a class A reserved subnet using a space instead of a newline for a delimiter:
prips -d 32 10.0.0.1 10.255.255.255
Display every fourth address in a weird block:
prips -i 4 192.168.32.7 192.168.33.5
Determine the smallest CIDR block containing two addresses:
prips -c 192.168.32.5 192.168.32.11
DIAGNOSTICS
The prips utility exits 0 on success, and >0 if an error occurs.
SEE ALSO
ipsc(1), gipsc(1)
STANDARDS
No standards were harmed in the writing of the prips tool.
HISTORY
The prips tool was originally written by Daniel Kelly and later adopted by Peter Pentchev. This manual page was originally written by Juan
Alvarez for the Debian GNU/Linux system and later added to the prips distribution and converted to mdoc format by Peter Pentchev.
AUTHORS
Daniel Kelly <dan@vertekcorp.com>
Juan Alvarez <jalvarez@fluidsignal.com>
Peter Pentchev <roam@ringlet.net>
BUGS
Please report any bugs in the prips tool to its current maintainer, Peter Pentchev.
BSD
March 1, 2011 BSD