01-23-2008
Thanks DukeNuke2 & sparcguy. The solution works.
9 More Discussions You Might Find Interesting
1. Solaris
Hi ,
I am trying to configure a private LAN and corporate LAN on the same machien on Solaris 10.
How can I achieve this?
Thanks (1 Reply)
Discussion started by: deedee
1 Replies
2. UNIX for Advanced & Expert Users
Double question here ... Running on Debian Etch and Apache 2.0
1) Using mod_proxy and/or mod_proxy_http in apache 2.0.
The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies
3. IP Networking
I'm trying to plumb a new interface bge1 on my machine:
root@obms2-com-indianapolis-in:/root# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet... (3 Replies)
Discussion started by: R37ribution
3 Replies
4. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
5. IP Networking
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Discussion started by: lawstudent
3 Replies
6. Red Hat
I use red hat linx ES 4 ,5 , how can I start up attached screen to config the lan interface in command mode ???
Please advice in detailed ?? (1 Reply)
Discussion started by: chuikingman
1 Replies
7. Red Hat
Hi,
How can I config iptables to allow port forwarding from one WAN interface to second lan interface .
In my system I have one wan interface 61.93.204.56 (eth0),and lan interface 10.2.1.52(eth1)
I want to make port forward port no 22 from 61.93.204.56 to
port 22 , 10.2.1.52 , tcp and udp... (1 Reply)
Discussion started by: chuikingman
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. Solaris
Hello all,
I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0.
This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help.
Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies
LEARN ABOUT SUSE
openipmicmd
openipmicmd(1) An IPMI Command Interface openipmicmd(1)
NAME
openipmicmd - An IPMI Command Interface
SYNOPSIS
openipmicmd [-k entry-to-execute] <connection parms>
DESCRIPTION
The openipmicmd program allows a user to execute direct IPMI commands. It can work with direct interface with the OpenIPMI driver or with
IPMI LAN interfaces.
OPTIONS
-k entry-to-execute
Execute a single command an exit.
<connectionparms>
The parameters for the connection depend on the connection type. These are all described in openipmi_conparms (7)
COMMANDS
Once up, you can execute commands in the user interface. Note that commands and responses are asynchronous, you issue a command and the
interface returns immediately. When the response comes back, it will be dumped on your console. That's a little strange looking, but IPMI
is ansychronous underneath. Note that the -k option is synchronous, it will wait for the response or a timeout before returning.
0f lun netfn cmd [data1 [data2 ...]]
Send a command to the BMC you are connected to.
channel [ipmb] IPMB-addr lun netfn [seq] cmd [data1 [data2 ...]]
Send a command to a device on the IPMB bus. The "ipmb" string is optional. The seq must be provided if the netfn is a response (an
odd number). It must be the same sequence number that came in on the command in the "Command Sequence = seq" part of the command.
channel 00 IPMB-addr lun netfn cmd [data1 [data2 ...]]
Send a broadcast command to a device on the IPMB bus.
channel lan handle remote-swid local-swid lun netfn cmd [data1 [data ...]]
Send a command to a device over a LAN channel. Note that this not the same as a LAN connection. This sends a message through a
local BMC to a remote system that is hooked up with a LAN connection.
test_lat count command
Executes the given commands (one of the previous commands) count times and gives the average time per command to execute. Note that
"count" is hexadecimal.
help Display some help.
regcmd netfn cmd
Register to receive the given command. If the driver receives an external command, it will print it out. This only works with sys-
tem interface connections, it will not work on LAN connections.
unregcmd netfn cmd
Remove a command registration.
SEE ALSO
ipmi_ui(1), ipmilan(8), openipmi_conparms(7)
KNOWN PROBLEMS
The asychronous nature of the program can be annoying.
AUTHOR
Corey Minyard <cminyard@mvista.org>
OpenIPMI 05/13/03 openipmicmd(1)