01-23-2008
Thanks DukeNuke2 & sparcguy. The solution works.
9 More Discussions You Might Find Interesting
1. Solaris
Hi ,
I am trying to configure a private LAN and corporate LAN on the same machien on Solaris 10.
How can I achieve this?
Thanks (1 Reply)
Discussion started by: deedee
1 Replies
2. UNIX for Advanced & Expert Users
Double question here ... Running on Debian Etch and Apache 2.0
1) Using mod_proxy and/or mod_proxy_http in apache 2.0.
The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies
3. IP Networking
I'm trying to plumb a new interface bge1 on my machine:
root@obms2-com-indianapolis-in:/root# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet... (3 Replies)
Discussion started by: R37ribution
3 Replies
4. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
5. IP Networking
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Discussion started by: lawstudent
3 Replies
6. Red Hat
I use red hat linx ES 4 ,5 , how can I start up attached screen to config the lan interface in command mode ???
Please advice in detailed ?? (1 Reply)
Discussion started by: chuikingman
1 Replies
7. Red Hat
Hi,
How can I config iptables to allow port forwarding from one WAN interface to second lan interface .
In my system I have one wan interface 61.93.204.56 (eth0),and lan interface 10.2.1.52(eth1)
I want to make port forward port no 22 from 61.93.204.56 to
port 22 , 10.2.1.52 , tcp and udp... (1 Reply)
Discussion started by: chuikingman
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. Solaris
Hello all,
I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0.
This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help.
Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies
LEARN ABOUT DEBIAN
sptrfs
sptrfs.f(3) LAPACK sptrfs.f(3)
NAME
sptrfs.f -
SYNOPSIS
Functions/Subroutines
subroutine sptrfs (N, NRHS, D, E, DF, EF, B, LDB, X, LDX, FERR, BERR, WORK, INFO)
SPTRFS
Function/Subroutine Documentation
subroutine sptrfs (integerN, integerNRHS, real, dimension( * )D, real, dimension( * )E, real, dimension( * )DF, real, dimension( * )EF, real,
dimension( ldb, * )B, integerLDB, real, dimension( ldx, * )X, integerLDX, real, dimension( * )FERR, real, dimension( * )BERR, real,
dimension( * )WORK, integerINFO)
SPTRFS
Purpose:
SPTRFS improves the computed solution to a system of linear
equations when the coefficient matrix is symmetric positive definite
and tridiagonal, and provides error bounds and backward error
estimates for the solution.
Parameters:
N
N is INTEGER
The order of the matrix A. N >= 0.
NRHS
NRHS is INTEGER
The number of right hand sides, i.e., the number of columns
of the matrix B. NRHS >= 0.
D
D is REAL array, dimension (N)
The n diagonal elements of the tridiagonal matrix A.
E
E is REAL array, dimension (N-1)
The (n-1) subdiagonal elements of the tridiagonal matrix A.
DF
DF is REAL array, dimension (N)
The n diagonal elements of the diagonal matrix D from the
factorization computed by SPTTRF.
EF
EF is REAL array, dimension (N-1)
The (n-1) subdiagonal elements of the unit bidiagonal factor
L from the factorization computed by SPTTRF.
B
B is REAL array, dimension (LDB,NRHS)
The right hand side matrix B.
LDB
LDB is INTEGER
The leading dimension of the array B. LDB >= max(1,N).
X
X is REAL array, dimension (LDX,NRHS)
On entry, the solution matrix X, as computed by SPTTRS.
On exit, the improved solution matrix X.
LDX
LDX is INTEGER
The leading dimension of the array X. LDX >= max(1,N).
FERR
FERR is REAL array, dimension (NRHS)
The forward error bound for each solution vector
X(j) (the j-th column of the solution matrix X).
If XTRUE is the true solution corresponding to X(j), FERR(j)
is an estimated upper bound for the magnitude of the largest
element in (X(j) - XTRUE) divided by the magnitude of the
largest element in X(j).
BERR
BERR is REAL array, dimension (NRHS)
The componentwise relative backward error of each solution
vector X(j) (i.e., the smallest relative change in
any element of A or B that makes X(j) an exact solution).
WORK
WORK is REAL array, dimension (2*N)
INFO
INFO is INTEGER
= 0: successful exit
< 0: if INFO = -i, the i-th argument had an illegal value
Internal Parameters:
ITMAX is the maximum number of steps of iterative refinement.
Author:
Univ. of Tennessee
Univ. of California Berkeley
Univ. of Colorado Denver
NAG Ltd.
Date:
November 2011
Definition at line 163 of file sptrfs.f.
Author
Generated automatically by Doxygen for LAPACK from the source code.
Version 3.4.1 Sun May 26 2013 sptrfs.f(3)