NIC and Device NO to Change Post: 302153243

9 More Discussions You Might Find Interesting

1. Solaris

change NIC to 1000 Mbps full duplex

Hi all, I tried to use this command ndd -set /dev/eri adv_1000fdx_cap 1 but i get a "operation failed, Invalid argument" anyone can help ? Thanks

2. Red Hat

My device files change!!!!

Hi... this is the situation. I have a server with redhat Advance Server 3 and the operating system is installed in /dev/sda disk... when i include new Luns dinamically they take the following special files /dev/sdb and /dev/sdc.... ok.. until now is everything ok... but the problem begins...

3. UNIX for Advanced & Expert Users

%device line change

Hello and thank you in advance for any assistance. Working with SCO 5.0.5 our SCSI tape device is no longer working. Before we replace the unit I want to verify it's not related to a change someone may have made via mkdev tape. For years the boot message would list the tape device as this:...

4. UNIX for Dummies Questions & Answers

How to change tape device name.

I disconected external device which was configured as rmt0. When I connect it again and run cfgmgr device name has changed (internal drive which was rmt1 is now rmt0 and external drive was rmt0 and is rmt1) and I dont know how to back it out. The thing is that for all backups I use new modell...

5. Solaris

change NIC speed

how can we change the nic card speed please explain through commands & steps ???? and i want to change NIC speed 100 --1000Mbps and what is full & half duplex gives thanks in advance

6. Programming

Does PID change from device to other!!!!

we asked to create a sender and receiver for a signals. sender knows his receiver by it's(receiver) PID .... my question is if i go to other computer and run my program will the pid chages than the first pid i got from old computer?

7. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome....

8. UNIX for Beginners Questions & Answers

Configuring NIC device in Solaris 9 SPARC OS [QEMU]

I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only. ...

9. AIX

AIX - NIC device explanation need

Hello, I have some doubt about the NIC device on my AIX box. When using lsdev command / > lsdev -Cc adapter | grep en ent0 Available 03-00 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003) ent1 Available 03-01 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003) ent2...

LEARN ABOUT NETBSD

de

DE(4)							   BSD Kernel Interfaces Manual 						     DE(4)

NAME

     de -- DECchip 21040, 21140, 21141, 21142, and 21143 PCI Ethernet interface driver

SYNOPSIS

     de* at pci? dev ? function ?

     Configuration of PHYs may also be necessary.  See mii(4).

DESCRIPTION

     The de driver supports Ethernet and Fast Ethernet interfaces based on the Digital Equipment Corporation DECchip 21040, 21140, 21141, 21142,
     and 21143 model controllers for PCI bus.

     21040   10BASE-T and AUI/BNC
     21140   10BASE-T and 100BASE-TX
     21141   10BASE-T and 100BASE-TX
     21142   10BASE-T and 100BASE-TX
     21143   10BASE-T and 100BASE-TX

     Supported Network Interface Cards (NIC) include, but are not limited to:

     Accton EN1207i
     Cogent EM100
     Asante AsanteFAST
     DEC DE435
     DEC DE450
     DEC DE500
     SMC 9332
     Znyx NetBlaster ZX340 series (345, 348, 346)

     Generally, if the NIC is for PCI bus, and the major controller chip has the DIGITAL logo on it, with one of the model numbers above, the de
     driver should recognize and control it.  Beware, however, that many NIC manufacturers change the Ethernet controller chip without changing
     the product model number, and a physical inspection of the NIC, or a probe of the NIC with a PCI diagnostic tool is the only way to tell if a
     real DEC TULIP controller is present.

     Multi-port interfaces are typically configured as a PCI-PCI bridge with multiple de instances on the PCI bus on the other side of the bridge.

     DEC sold its semiconductor division to Intel.  In addition, there are many "knock-offs" of the DEC TULIP Ethernet controller chips; NICs
     based on these chips are handled by the tlp(4) driver.

     This de driver should not be confused with the NetBSD VAX de driver for the DEC DEUNA/DELUA Ethernet controller for UniBus.

SEE ALSO

     ifmedia(4), intro(4), mii(4), pci(4), tlp(4), ifconfig(8)

     http://www.adaptec.com/, http://www.asante.com/, http://www.smc.com/, http://www.znyx.com/

HISTORY

     The de driver first appeared in NetBSD 1.1

AUTHORS

     Matt Thomas <matt@3am-software.com>.

BSD
								 February 11, 2000							       BSD

9 More Discussions You Might Find Interesting

1. Solaris

change NIC to 1000 Mbps full duplex

Discussion started by: DarReNz

2. Red Hat

My device files change!!!!

Discussion started by: lenux78

3. UNIX for Advanced & Expert Users

%device line change

Discussion started by: sighbrrguy

4. UNIX for Dummies Questions & Answers

How to change tape device name.

Discussion started by: fraydey

5. Solaris

change NIC speed

Discussion started by: wkbn86

6. Programming

Does PID change from device to other!!!!

Discussion started by: fwrlfo