Sponsored Content
Operating Systems Linux Debian Kernel source not found. (can't install network card drivers) Post 302150489 by Virtuality on Tuesday 11th of December 2007 04:20:45 PM
Old 12-11-2007
..........................................................

kernel-source-2.6.18-5-686 doesn't exist outside of repositories that apt-get uses.

I can not use apt-get, therefore I can not obtain kernel-source-2.6.18-5-686. That's the problem.

I'd love to install it and I've been TRYING to, except I have to actually get the file first, I've searched every repository on the internet and nothing.
 

6 More Discussions You Might Find Interesting

1. AIX

Hp Laserjet 4600 jetdirct card printr drivers

Iam facing dificulty in installing hp color laserjet 4600 printer in IBM-AIX 5.1. Where i can find a drivers for this printer ,Or pls suggest me another way to get it install this printer Thanx Ravi (2 Replies)
Discussion started by: ravikantchavan
2 Replies

2. Solaris

Unable to install the Network Card

Hi, After I installed Solaris 10 in the Intel platform (chipset 865*) network card was not detected, were shall I get this driver? iam new to Solaris. (2 Replies)
Discussion started by: pravin_2929
2 Replies

3. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies

4. Solaris

Network card drivers for solaris?

Hi all, i have configured my solaris 5 .10 for internet connection by editing the files /etc/hosts/,/etc/resolve.config,/etc/defalutrouter and nsswitchconfig . during installation i was not requested for ip adddress even i plugged network cable. am i need to install any network card... (2 Replies)
Discussion started by: srikanthg
2 Replies

5. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies

6. UNIX for Dummies Questions & Answers

How to install kernel source?

During installation of one of driver i needed to Remove any earlier version drivers using make clean -r command. Where i m getting following error. # make clean -r Kernel source is not installed make: *** Error 1 My kernel version # uname -r 2.6.18-128.2.1.4.9.el5xen Where... (4 Replies)
Discussion started by: pinga123
4 Replies
DUMMY_CS(4)						     Kernel Interfaces Manual						       DUMMY_CS(4)

NAME
dummy_cs - PCMCIA dummy device driver SYNOPSIS
insmod dummy_cs.o [pc_debug=n] [free_ports=n] [irq_list=i,j,...] DESCRIPTION
The dummy_cs module has two purposes. It is intended as a demonstration of how to write the PCMCIA interface code for a client driver, and the source code is heavily commented. It is also written to function as a sort of generic ``point enabler'': when bound to any PCMCIA IO card, it will read the card's Configuration Information Structure, and configure the card appropriately. The configuration includes set- ting up IO and memory windows, configuring the card for interrupts, and initializing the card's PCMCIA configuration registers. It turns out that many cards report incomplete or inaccurate configuration information, due to vendor carelessness and the complexity of the data format. A vendor driver can generally take for granted many configuration details, so there is not much incentive for vendors to ensure that the on-card information is complete. Thus, the dummy_cs module is limited by its generality: since it makes no assumptions about card types, it is forced to rely on the card information, for better or worse. PARAMETERS
pc_debug=n Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero value enables debugging. free_ports=n A flag indicating if the IO ports allocated for the card should be freed from the kernel resource maps. This is useful if the dummy driver is being used to configure a card in preparation for loading a specific PCMCIA-unaware driver. The default is 0 (false). irq_list=i,j,... Specifies the set of interrupts that may be allocated by this driver. AUTHOR
David Hinds - dahinds@users.sourceforge.net SEE ALSO
cardmgr(8), pcmcia(5). pcmcia-cs 2000/06/12 21:24:47 DUMMY_CS(4)
All times are GMT -4. The time now is 12:42 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy