Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
i purchased, what was labeled as a 4-port fast ethernet sbus card from ebay.
i installed it in my ultra1, and it seems to be working fine. how can i determine if the card is infact a fast ethernet card vs. the standard ethernet 4-port card? (7 Replies)
Hi,
I have my server which has LAN with above model build onboard my Dell Server, I got this driver from SCO Unix website but yet to identify the following option:
1. PCI Slot-
2. Bus-
3. Device-
4. Function-
Would anyone please kindly advice what should the... (0 Replies)
Hi All,
i have a problem with my database server using sun machine v440 and sunOS 5.9 on ethernet, i've checked on system log /var/adm/messages and found much error messages like shown below :
Sep 21 16:14:48 dbs genunix: WARNING: ce0: fault detected external to device; service degraded
Sep... (2 Replies)
Hey. how do i configure the Lance Ethernet in my SS5
i must use DHCP to get Internet access. i have tried sys-unconfig and ifconfig le0 plumb and dhcp. but no cigar. how do i configure ?
i have had some problems with the /etc/hosts dir. it says it dosent exist and when i try to create it it says... (1 Reply)
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
I have a server with 6 Ethernet ports. 4 are the the motherboard based 1 GBE ports and 2 are 10 GBE ports on NICs.
I have set these all up with static IP addresses and use the standard /etc/nsswitch.files. My IP addresses are
net0 192.168.1.82
net1 192.168.2.82
and so on till
net5... (4 Replies)
Discussion started by: ashlaw
4 Replies
LEARN ABOUT NETBSD
sys-unconfig
sys-unconfig(1M) System Administration Commands sys-unconfig(1M)NAME
sys-unconfig - undo a system's configuration
SYNOPSIS
/usr/sbin/sys-unconfig
DESCRIPTION
The sys-unconfig command is used to restore a system's configuration to an "as-manufactured" state, ready to be reconfigured again. The
system's configuration consists of hostname, Network Information Service (NIS) domain name, timezone, IP address, IP subnet mask, and root
password. This operation is the inverse of those performed by the sysidnet(1M), sysidns(1M), and sysidsys(1M) programs run at boot. See
sysidtool(1M).
sys-unconfig does the following:
o Saves current /etc/inet/hosts file information in /etc/inet/hosts.saved.
o If the current /etc/vfstab file contains NFS mount entries, saves the /etc/vfstab file to /etc/vfstab.orig.
o Restores the default /etc/inet/hosts file.
o Removes the default hostname in /etc/hostname.interface files for all interfaces configured when this command is run. To determine
which interfaces are configured, run the command 'ifconfig-a'. The /etc/hostname.interface files corresponding to all of the inter-
faces listed in the resulting output, with the exception of the loopback interface (lo0), will be removed.
o Removes the default domainname in /etc/defaultdomain.
o Restores the timezone to PST8PDT in /etc/TIMEZONE.
o Disables the Network Information Service (NIS) and Network Information Service Plus (NIS+) if either NIS or NIS+ was configured.
o Removes the file /etc/inet/netmasks.
o Removes the file /etc/defaultrouter.
o Removes the password set for root in /etc/shadow.
o Removes the file /etc/.rootkey.
o Executes all system configuration applications. These applications are defined by prior executions of a sysidconfig -a application.
(See sysidconfig(1M)). When sys-unconfig is run, all system configuration applications are passed one argument, -u.
o Removes the file /etc/resolv.conf.
o Disables LDAP by removing /var/ldap/ldap_client_cache, /var/ldap/ldap_client_file, /var/ldap/ldap_client_cred, and
/var/ldap/cachemgr.log.
o Regenerates keys for sshd(1M).
When sys-unconfig is finished, it performs a system shutdown. sys-unconfig is a potentially dangerous utility and can only be run by the
super user.
FILES
/etc/default/init process control initialization
/etc/defaultdomain
/etc/defaultrouter
/etc/hostname.interface
/etc/inet/hosts host name database
/etc/inet/netmasks network mask database
/etc/nodename
/etc/.rootkey super-user's secret key
/etc/shadow shadow password file
/etc/vfstab virtual file system table
/var/nis/NIS_COLD_START
/var/yp/binding/*/ypservers
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWadmap |
+-----------------------------+-----------------------------+
SEE ALSO init(1M), kdmconfig(1M), sshd(1M), sysidconfig(1M), sysidtool(1M), hosts(4), netmasks(4), shadow(4), attributes(5)NOTES
sys-unconfig is not available on diskless clients.
SunOS 5.10 4 Jun 2004 sys-unconfig(1M)