10-12-2007
internet <---> router <------- subnet A ---> gateway <--- subnet B ----->
So the box gateway needs at least two network interfaces, each with separate IP addresses.
I also had to add a static link to the router to get from the router to subnet B using gateway as the default route for that subnet.
The gateway runs dhcpd as well as having ip-forwarding turned on. For good measure it also runs bind9 with my local name server which then forwards unknown requests onto the router.
10 More Discussions You Might Find Interesting
1. IP Networking
I am running solaris 8 on the ultra 5 sparc. I used to have a static ip address set up and now I've moved and I'm trying to get dhcp working. I have read many man pages. My latest attempt was trying to use the ifconfig command to set this up but I'm not sure how to use it. How does my gateway... (9 Replies)
Discussion started by: mhunting
9 Replies
2. IP Networking
I have managed to setup my Solaris box to receive an IP number from a DHCP server. In addition, I can ping and telnet between my dhcp server and my solaris box using the IP number. However, I can't resolve addresses by name from my solaris box.
In my nsswitch.conf file I have:
hosts: dns
... (4 Replies)
Discussion started by: marist89
4 Replies
3. Solaris
How is it possible to derive the very next IP that the solaris dhcp server is going to assign to the next host that requests? (0 Replies)
Discussion started by: ne0phyte
0 Replies
4. Solaris
Can any one tell me how to stop DHCP service on Solaris 10 so that it should not start nextime when the system is rebooted. (2 Replies)
Discussion started by: shabu
2 Replies
5. UNIX for Dummies Questions & Answers
I have a new solaris machine and I am trying to bring the same on network. The IP assignemnt is via DHCP. I want to know as which files need to be modified to include DHCP server IP in order that the machine gets its IP via DHCP server.
Thanks in Advance. :) (1 Reply)
Discussion started by: Ashvin Gaur
1 Replies
6. Solaris
Hello,
I need to configure a Cisco VLAN Accesspoint with DHCP using Solaris
dhtadm & pntadm
Network: 10.10.122.0 255.255.255.0
Default Router 10.10.122.1
Scope Range 10.10.122.10 - 254
Option 60 “Cisco AP c1142”
Option 43 ... (0 Replies)
Discussion started by: fredy82
0 Replies
7. Solaris
Dear All,
I have following configuration solaris 10 host
interface e1000g0 hold IP 10.124.73.178 having internet access natted to public ip on cisco switch
interface e1000g1 hold IP 192.168.8.10 DHCP server with DHCP client IP ranges 192.168.8.11 to 192.168.8.15
/etc/defaultrouter hold... (4 Replies)
Discussion started by: patel1678
4 Replies
8. Red Hat
I have 2 problems. Dhcp is not setting dns and after I manually set my dns it changes to garbage.
I literally just used command to set dns which is a good copy of resolv.conf:
sudo cp /home/bob/Desktop/scripts_9-12-2011/resolv.conf /etc/resolv.confHere is a copy of my resolv.conf.
#... (5 Replies)
Discussion started by: cokedude
5 Replies
9. Solaris
I need to find out the MAC address of an IP leased from DHCP server .
For Eg:-i need to know the MAC of the below mentioned IP at the below mentioned time .
IP : 172.16.28.90
Date :Sunday July 2nd 2011
Time : 14.07.2011
OS -Solaris 10
Vital QIP IP management software using to... (0 Replies)
Discussion started by: sandeep.tk
0 Replies
10. Solaris
Hi All,
Could you please let me know how can we check whether any given solaris machien is using DHCP or not.
is ps -ef | grep dhcp is full proof method or is their any other way. (10 Replies)
Discussion started by: omkar.jadhav
10 Replies
LEARN ABOUT HPUX
map-mbone
map-mbone(1M) map-mbone(1M)
NAME
map-mbone - Multicast Router Connection Mapper
SYNOPSIS
debuglevel] retries] timeout] [multicast-router]
DESCRIPTION
requests the multicast router connection information from the multicast-router, and prints the information to the standard out. sends out
the ASK_NEIGHBORS igmp message to the multicast-router. When the multicast-router receives the request, it sends back its configuration
information. multicast-router can be either an ip address or a system name.
If the multicast-router is not specified, flood mode is on by default and the igmp request message is sent to all the multicast router on
the local network. With flood mode on, when finds new neighbor routers from the replies, it will send the same igmp request to the new
neighbor routers. This activity continues until no new neighbor routers are reported in the replies.
The command line options are:
Sets the level for printing out the debug message. The default is 0,
which prints only error and warning messages. Debug level three prints most the messages.
Sets the retry times to poll the routing daemon for information. The
default is 1.
It specifies the timeout value in seconds for waiting the reply. The
default value is 2 seconds.
Sets the flood mode on. It is the default value when no multicast-router is given on the command line input.
Generates output in GRaphEd format.
Disable DNS lookup for the multicast router names.
The output contains the interface configuration information of the requested router(s). The format for each interface output is:
If there are multiple neighbor routers on one interface, they will all be reported. The neighbor_name will not be printed if the option is
specified on the command line.
The possible values for are:
Neighbors are reached via tunnel.
The tunnel uses IP source routing.
The interface is down.
The interface is administratively disabled for multicast routing.
The local router is the querier of the subnet.
The format of the GRaphEd output is:
If there is no neighbor router on an interface, then a will be put next to the node_name. If there are multiple neighbor routers on one
interface, all of them will be reported. The possible values for are:
The neighbor is reached via tunnel.
The neighbor is on the same network/subnet.
The interface is down.
Please see mrouted(1M) for and
EXAMPLES
Querying for the multicast router connection information.
127.0.0.1 (localhost) [version 3.3]:
193.2.1.39 -> 0.0.0.0 (all-zeros-broadcast) [1/1/disabled]
15.13.106.144 -> 15.255.176.33 (matmos.hpl.hp.com) [10/1/tunnel]
15.13.106.144 -> 15.17.20.7 (hpspddc.vid.hp.com) [10/1/tunnel/down]
Querying for multicast router connectivity with option:
GRAPH "Multicast Router Connectivity: Wed Feb 1 17:34:59 1995"=UNDIRECTED
252537488 {$ NP 1440 1060 $} "hpntc1t.cup.hp.com*"
;
252538974 {$ NP 940 1120 $} "hpntcbs.cup.hp.com"
252537488 "10/1E"
252539807 "1/1P"
;
252539807 {$ NP 1590 1150 $} "hpntc1h.cup.hp.com*"
;
Note
must be run as root.
AUTHOR
was developed by Pavel Curtis.
SEE ALSO
mrouted(1M), mrinfo(1M).
map-mbone(1M)