Hi all,
I am processing a file with awk that looks like this:
"
0.0021 etc
0.0123 etc
0.1234 etc
...
0.5324 etc
0.5434 etc
0.6543 etc
...
1.0344 etc
1.1344 etc
...
1.5345 etc
1.5632 etc
"
I need to print out only the lines that have '0' or '5' after the comma, plus I need only... (11 Replies)
:confused:Hi,
I have got results from my simulation and I did extract the time field from the results file into new file. Then I was trying to calculate no. of occurrence for each set of time. However, I couldn't.
For example :
0.2 --
0.2 --
0.21016 --
0.21016 --
0.21016 --
.
.
.... (12 Replies)
Thanks for the help yesterday. I have a little modification today,
I am trying the following:
i have a log file of a webbap which logs in the following pattern:
2011-08-14 21:10:04,535 blablabla ERROR Exception1 blablabla
bla
bla
bla
bla
2011-08-14... (2 Replies)
Hi everyone, I'm a new member at the forum
I have a file like this: field 2 values are either 0 or negative. file test4:
100815 -20
118125 0
143616 0
154488 0
154488 0
154488 -6
196492 -5
196492 -9
196492 -7
27332 0
29397 0
I would like to print a... (1 Reply)
Hi everyone, I'm a new member at the forum I mistakenly posted this elsewhere too.
I have a file like this: field 2 values are either 0 or negative. file test4:
100815 -20
118125 0
143616 0
154488 0
154488 0
154488 -6
196492 -5
196492 -9
196492 -7
27332 0... (5 Replies)
My file contains like this on 10 th line
NM1*IL*1*
awk '/NM1/{print NR}' *.dat
output is 10
awk '/NM1*IL*1*/{print NR}' *.dat
output is Nothing
but im expecting 10 on second code as well . (4 Replies)
Hi,
let's say an input looks like:
A|C|C|D
A|C|I|E
A|B|I|C
A|T|I|B
as the title of the thread explains, I am trying to get something like:
1|A=4
2|C=2|B=1|T=1
3|I=3|C=1
4|D=1|E=1|C=1|B=1
i.e. a count of every character in each field (first column of output) independently, sorted... (4 Replies)
Assume a string that contains one or multiple occurrences of three different keywords (abbreviated as "kw"). I would like to replace kw2 with some other string, say "qux". Specifically, I would like to replace that occurrence of kw2 that is the first one that is preceded by kw1 somewhere in the... (4 Replies)
Hi all,
I am looking for to filter out based on 7th character and list the number of occurrence based on the 7th character if p , d , o or m
1. if 7th character is p , Output should be: p_hosts = N
2. if 7th character is d , Output should be: d_hosts = N
3. if 7th character is o , Output... (10 Replies)
Discussion started by: rveri
10 Replies
LEARN ABOUT DEBIAN
mrtg-ping-probe
MRTG-PING-PROBE(1) General Commands Manual MRTG-PING-PROBE(1)NAME
mrtg-ping-probe - ping probe module for Multi Router Traffic Grapher
DESCRIPTION
mrtg-ping-probe is a ping probe module for MRTG 2.x. It is used to monitor the round trip time and packet loss to networked devices. MRTG
uses the output of mrtg-ping-probe to generate graphs visualizing minimum and maximum round trip times or packet loss.
mrtg-ping-probe is not run directly, but is called by MRTG as a helper when it needs to determine ping time to a host.
Act responsibly: do not use mrtg-ping-probe to ping devices without the owner's permission. Just imagine if 10,000 people decided to ping
your hosts! mrtg-ping-probe is meant to be used within your network to get round trip time performance figures for your network.
OPTIONS
To use mrtg-ping-probe you need to configure MRTG to call it from within the definition of a target host. This is done in the MRTG config
file, which is usually /etc/mrtg.conf.
Here's an example snippet: change the target name and IP address to suit your needs.
Target[your.target.ping]: `/usr/bin/mrtg-ping-probe 123.456.789.123`
SetEnv[your.target.ping]: MRTG_INT_IP="123.456.789.123" MRTG_INT_DESCR="ping"
MaxBytes[your.target.ping]: 100
AbsMax[your.target.ping]: 200
Options[your.target.ping]: gauge, growright
YLegend[your.target.ping]: ping time (ms)
ShortLegend[your.target.ping]: ms
Legend1[your.target.ping]: Maximum Round Trip Time in ms
Legend2[your.target.ping]: Minimum Round Trip Time in ms
Legend3[your.target.ping]: Maximal 5 Minute Maximum Round Trip Time in ms
Legend4[your.target.ping]: Maximal 5 Minute Minimum Round Trip Time in ms
LegendI[your.target.ping]: Max:
LegendO[your.target.ping]: Min:
Pay close attention to the backticks in the first line which tell MRTG to execute the nominated external program. Note also that you need
to use the "gauge" option, since the results of subsequent ping probes are independant values and not an incrementing counter.
SEE ALSO mrtg(1).
The latest release of mrtg-ping-probe can be found on the web at http://pwo.de/projects/mrtg/
AUTHOR
This manual page was written by Jonathan Oxer <jon@debian.org>, for the Debian project (but may be used by others).
April 14, 2003 MRTG-PING-PROBE(1)