09-21-2007
have you checked the switch to which the box is connected? looks like an autoneg problem...
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have been looking for info on how to aggregate 2 ore 3 NIC's into into one big pipe. Any advice would be appreciated.
-Chuck (4 Replies)
Discussion started by: 98_1LE
4 Replies
2. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
3. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
4. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
5. Solaris
Hey. i have been trying to configure the on board Ethernet in My Sparcstation 5, i have spent a lot of time on the ifconfig man pages. but it could really be nice with some pro. help. i don't think the interface is running . i don't know what name the interface have, le0 eth0 et0, it just says no... (4 Replies)
Discussion started by: mads-nielsen
4 Replies
6. Solaris
Hey. how do i configure the Lance Ethernet in my SS5
i must use DHCP to get Internet access. i have tried sys-unconfig and ifconfig le0 plumb and dhcp. but no cigar. how do i configure ?
i have had some problems with the /etc/hosts dir. it says it dosent exist and when i try to create it it says... (1 Reply)
Discussion started by: mads-nielsen
1 Replies
7. Solaris
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies
8. Solaris
Hello professional,
I am using Solaris 8 x86 (32 bits) running on Vmware 6.x.x
my vmware configuration:
config.version = "8"
virtualHW.version = "6"
scsi0.present = "TRUE"
memsize = "1024"
ide0:0.present = "TRUE"
ide0:0.fileName = "Other.vmdk"
ide1:0.present = "TRUE"... (0 Replies)
Discussion started by: draggy
0 Replies
9. Solaris
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT CENTOS
genrbox
GENBOX(1) General Commands Manual GENBOX(1)
NAME
genrbox - generate a RADIANCE description of a box
SYNOPSIS
genrbox mat name xsiz ysiz zsiz [ -i ][ -r rad | -b bev ]
DESCRIPTION
Genbox produces a RADIANCE scene description of a parallelepiped with one corner at the origin and the opposite corner at (xsiz, ysiz,
zsiz). The sides of the box will be parallel to the three coordinate planes. The surfaces that make up the box will be modified by mat
and their identifiers will begin with name. The -i option can be used to produce a box with inward directed surface normals. The -r
option can be used to specify the radius for rounded edges. The -b option can be used to specify the indentation for beveled edges.
EXAMPLE
To produce a rectangular box made of wood with beveled edges:
genrbox wood box1 5 8 3 -b .5 > box1
AUTHOR
Greg Ward
BUGS
Because spheres and cylinders are used to construct boxes with rounded edges, a transparent box of this type appears quite messy.
SEE ALSO
genrev(1), gensurf(1), genworm(1), rpict(1), rvu(1), xform(1)
RADIANCE
11/15/93 GENBOX(1)