07-03-2007
If you have a /dev/random you could pipe it into "dd" to write directly over the complete partition.
dd if=/dev/random of=/dev/partition
then do mkfs on the partition again.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
Discussion started by: yls177
3 Replies
2. UNIX for Dummies Questions & Answers
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Discussion started by: jtp51
1 Replies
3. Solaris
hi experts,
i had installed and do mirroring with sun solaris 8 v890 sparc, i had forget to make a partition for directory /data, i have 6 hard drive with disk0 mirror disk1(for root,var,opt,etc) ,disk2 mirror disk3(for /data2) and disk4 mirror disk5(for /data3), how to make a new partition for... (2 Replies)
Discussion started by: bucci
2 Replies
4. UNIX Desktop Questions & Answers
Among other critical Linux challenges terminal code looms large.
Got this far and think I am right. See attachment and when I open I get
Error opening file '/home/allen/data1/ Permission denied
could someone give me the chown code or anything else I lack
allen@allen-laptop:~$ sudo mkdir... (2 Replies)
Discussion started by: 77yrold
2 Replies
5. Shell Programming and Scripting
Hi, Appreciated if anyone can throw some hint
I have a file format like this:
old(1): PRCNCP
1
old(2): PRSKU ... (6 Replies)
Discussion started by: netbanker
6 Replies
6. Solaris
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies
7. Red Hat
Hello,
I have been going through our environment and I see we have a few servers with LVM's setup and the file system type is still set to "83" within fdisk. If I change this to "8e", will it hurt the data or cause any loss? I need to know for sure before I make the change. (1 Reply)
Discussion started by: s ladd
1 Replies
8. Filesystems, Disks and Memory
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Discussion started by: edydsuranta
2 Replies
9. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
WREN(3) Library Functions Manual WREN(3)
NAME
wren, ata - hard disk interface
SYNOPSIS
bind #H[drive] /dev
bind #w[target[.lun]] /dev
/dev/hd0disk
/dev/hd0partition
/dev/sd0disk
/dev/sd0partition
...
DESCRIPTION
The hard disk interfaces (wren, #w, is a SCSI disk; ata, #H, is an IDE or ATA disk) serve a one-level directory giving access to the hard
disk partitions. The parameter to attach defines the numerical SCSI target and logical unit number or the IDE drive number to access.
Both default to zero.
Each partition name is prefixed by hd and the numeric drive identifier. The partition always exists and covers the entire disk. The size
of each partition as reported by stat(2) is the number of bytes in the partition, so the size of is the size of the entire disk.
The partition also always exists; it is the last block on the disk for SCSI, second to last for IDE. If it contains valid partition data,
those partitions will be visible as well. Every time the device is bound, the partitions are updated to reflect any changes in the parti-
tion file.
The format of the partition file is the string
plan9 partitions
on a line, followed by partition specifications, one per line, consisting of a name and textual strings for the block start and limit for
each partition on the disk.
The program prep(8) writes the partition table for the disk; its use is preferred to writing it by hand.
SEE ALSO
prep(8), scsi(3)
SOURCE
/sys/src/9/port/devwren.c
/sys/src/9/pc/devata.c
WREN(3)