06-20-2007
WOW, this is great. Exactly what i needed.
Thank you.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Dummies Questions & Answers
I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is... (3 Replies)
Discussion started by: 98_1LE
3 Replies
3. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
4. IP Networking
What are the steps between "ifconfig eth0 UP" and "net_device->open"?
ifconfig eth0 UP =>
ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) =>
????? => what are these steps?
net_device->open
Thanks! (1 Reply)
Discussion started by: samuncle
1 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT LINUX
snmpa_network_interface
snmpa_network_interface(3erl) Erlang Module Definition snmpa_network_interface(3erl)
NAME
snmpa_network_interface - Behaviour module for the SNMP agent network interface.
DESCRIPTION
This module defines the behaviour of the agent network interface. A snmpa_network_interface compliant module must export the following
functions:
* start_link/4
* info/1
* get_log_type/1
* set_log_type/2
* verbosity/2
The semantics of them and their exact signatures are explained below.
But this is not enough. There is also a set of mandatory messages which the network interface entity must be able to receive and be able to
send. This is described in chapter snmp_agent_netif .
EXPORTS
start_link(Prio, NoteStore, MasterAgent, Opts) -> {ok, Pid} | {error, Reason}
Types Prio = priority()
NoteStore = pid()
MasterAgent = pid()
Opts = [opt()]
opt() = {verbosity, verbosity()} | {versions, versions()} | term()
versions() = [version()]
version() = v1 | v2 | v3
Start-link the network interface process.
NoteStore is the pid of the note-store process and MasterAgent is the pid of the master-agent process.
Opts is an (basically) implementation dependent list of options to the network interface process. There are however a number of
options which must be handled: versions and verbosity .
info(Pid) -> [{Key, Value}]
Types Pid = pid()
The info returned is basically up to the implementer to decide. This implementation provided by the application provides info about
memory allocation and various socket information.
The info returned by this function is returned together with other info collected by the agent when the info function is called
(tagged with with the key net_if ).
verbosity(Pid, Verbosity) -> void()
Types Pid = pid()
Verbosity = verbosity()
Change the verbosity of a running network interface process.
get_log_type(Pid) -> {ok, LogType} | {error, Reason}
Types Pid = pid()
LogType = atl_type()
Reason = term()
The Audit Trail Log is managed by the network interface process. So, it is this process that has to retrieve the actual log-type.
set_log_type(Pid, NewType) -> {ok, OldType} | {error, Reason}
Types Pid = pid()
NewType = OldType = atl_type()
Reason = term()
The Audit Trail Log is managed by the network interface process. So, it is this process that has to do the actual changing of the
type.
See set_log_type for more info.
Ericsson AB snmp 4.19 snmpa_network_interface(3erl)