06-20-2007
WOW, this is great. Exactly what i needed.
Thank you.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Dummies Questions & Answers
I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is... (3 Replies)
Discussion started by: 98_1LE
3 Replies
3. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
4. IP Networking
What are the steps between "ifconfig eth0 UP" and "net_device->open"?
ifconfig eth0 UP =>
ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) =>
????? => what are these steps?
net_device->open
Thanks! (1 Reply)
Discussion started by: samuncle
1 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT SUSE
ifcfg-bonding
IFCFG-BONDING(5) Network configuration IFCFG-BONDING(5)
NAME
ifcfg-bonding - interface bonding configuration
SYNOPSIS
/etc/sysconfig/network/ifcfg-bond*
Bonding Interfaces
To setup a bonding interface you need a configuration file ifcfg-bond<X> with the usual network settings. But you must add additional vari-
ables
BONDING_MASTER
must be set to 'yes' to identify this interface as a bonding interface
BONDING_SLAVE_<X>
here you specify the interface name representing the slave network interfaces.
BONDING_MODULE_OPTS
contains bonding options. Here you can set interface timeouts or working modes ('mode=active-backup' for backup mode). For addi-
tional information take a look into the documentation mentioned at the bottom. Note, that this options are not passed as parameters
to the bonding kernel module any more, but set via sysfs interface. This variable will be renamed in the feature.
BONDING_SKIP_REMOVE_WORKAROUND
When set to "yes", a bonding interface will be not removed while ifdown any more to avoid problems, e.g. when some third party ker-
nel module, such as Veritas 'llt' module, does not react correctly to the UNREGISTER event and does not remove its references to the
bonding interface causing all network related operation to stuck.
Note: the bonding options are not reverted when this option is enabled and it is required to either explicitly keep the old options
and set them to their default setting on bonding configuration changes or to reboot.
Example
Example for a bonding interface on eth0 and eth1 using the backup mode
ifcfg-bond0
STARTMODE='onboot'
BOOTPROTO='static'
IPADDR='192.168.0.1/24'
BONDING_MASTER='yes'
BONDING_SLAVE_0='eth0'
BONDING_SLAVE_1='eth1'
BONDING_MODULE_OPTS='mode=active-backup miimon=100'
Additional Information
For additional and more general information take a look into /usr/src/linux/Documentation/networking/bonding.txt. Maybe you need to
install the kernel sources to get this additional documentation.
The configuration of routes for this kind of interface does not differ from ordinary interfaces. See man routes for details.
BUGS
Please report bugs at <http://www.suse.de/feedback>
AUTHOR
Christian Zoz <zoz@suse.de> -- ifup script
Wilken Gottwalt <wgottwalt@suse.de> -- ifcfg-bonding manual page
SEE ALSO
ifcfg(5), ifup(8).
sysconfig April 2005 IFCFG-BONDING(5)