Changing Network Interface hme1 to hme0 Post: 302120333

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. UNIX for Advanced & Expert Users

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0...

3. Solaris

Changing the default network Interface

Hello: I have a Sun E250 with an on board hme0 interface, I also have installed a gigabit ethernet (GE0) card. When the system boots up it defaults to the on board Hme0 card. I would like it to default to the GE0 card. I believe this can be done thru the OK prompt using the show-nets and...

4. Solaris

Network interface not found ?

Hello, I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else. - I dont have any /etc/hostnames.xxx - ifconfig -a shows only the loopback - kstat -c net shows only the loopback ... Any...

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

6. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

7. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT CENTOS

halt

HALT(8) 							       halt								   HALT(8)

NAME

       halt, poweroff, reboot - Halt, power-off or reboot the machine

SYNOPSIS

       halt [OPTIONS...]

       poweroff [OPTIONS...]

       reboot [OPTIONS...]

DESCRIPTION

       halt, poweroff, reboot may be used to halt, power-off or reboot the machine.

OPTIONS

       The following options are understood:

       --help
	   Prints a short help text and exits.

       --halt
	   Halt the machine, regardless of which one of the three commands is invoked.

       -p, --poweroff
	   Power-off the machine, regardless of which one of the three commands is invoked.

       --reboot
	   Reboot the machine, regardless of which one of the three commands is invoked.

       -f, --force
	   Force immediate halt, power-off, reboot. Do not contact the init system.

       -w, --wtmp-only
	   Only write wtmp shutdown entry, do not actually halt, power-off, reboot.

       -d, --no-wtmp
	   Do not write wtmp shutdown entry.

       --no-wall
	   Do not send wall message before halt, power-off, reboot.

EXIT STATUS

       On success, 0 is returned, a non-zero failure code otherwise.

NOTES

       These are legacy commands available for compatibility only.

SEE ALSO

       systemd(1), systemctl(1), shutdown(8), wall(1)

systemd 208																   HALT(8)

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Discussion started by: witt

2. UNIX for Advanced & Expert Users

network interface problem

Discussion started by: sc2005