06-05-2007
It would, though the reboot can be avoided by using ifconfig.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
3. Solaris
Hello:
I have a Sun E250 with an on board hme0 interface, I also have installed a gigabit ethernet (GE0) card. When the system boots up it defaults to the on board Hme0 card. I would like it to default to the GE0 card. I believe this can be done thru the OK prompt using the show-nets and... (1 Reply)
Discussion started by: rambo15
1 Replies
4. Solaris
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
reboot(2) System Calls Manual reboot(2)
NAME
reboot - Reboots system or halts processor
SYNOPSIS
#include <sys/reboot.h>
void reboot( int howto );
PARAMETERS
Specifies a mask of options.
DESCRIPTION
The reboot() function restarts the system. The startup is automatic and brings up /vmunix in the normal, nonmaintenance mode. The calling
process must have superuser privilege to run this function successfully. However, a reboot is invoked automatically in the event of unre-
coverable system failures.
The following options, defined in the sys/reboot.h include file are passed to the new kernel or the new bootstrap and init programs. They
are supplied as values to the howto parameter. The default, causing the system to reboot in its usual fashion. Dump kernel memory before
rebooting; see the savecore command for more information. The processor is simply halted; no reboot takes place. The disks are not sync'd
before the processor is halted or rebooted. Normally, the disks are sync'd (see the sync() command) before the processor is halted or
rebooted. Because the disks are not sync'd with the RB_NOSYNC option, loss of data may result from using it.
When no options are given (that is, RB_AUTOBOOT is used), the system is rebooted from file vmunix in the root file system of unit 0 (zero)
of a disk chosen in a processor-specific way. (see the fsck command).
RETURN VALUES
If successful, this call does not return. Otherwise, a -1 is returned and errno is set to indicate the error.
ERRORS
If the reboot() function fails, errno may be set to the following value: The calling process does not have appropriate privilege.
RELATED INFORMATION
Commands: crashdc(8),
halt(8), init(8), reboot(8), savecore(8) delim off
reboot(2)