05-10-2007
Can you create a seperate VG on this PV? This will tell you whether the disk is in fact defective.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
HI
I'm using red hat 7.0 and i've tried to find my network card, because it wasn't recognised at install time.
I issued this commands "modprobe ne" and "modprobe 3c59x"
and i got the message
/lib/modules/2.2.16-22/net/ne.0: insmod failed.
At this point i suppose to get this... (2 Replies)
Discussion started by: IMOTEB
2 Replies
2. AIX
Hello,
I have an AIX 5.1 server. Model : 7029-6E3. The users of this server have forgotted the root password and I am now supposed to reset it. I boot through the AIX 5.1 CD and try to go to the maitenance mode. But I am facing this issue, where, the hard disk does not recognised during this... (1 Reply)
Discussion started by: sjsowmya
1 Replies
3. UNIX for Dummies Questions & Answers
I've just replaced the secondary disk drive (was 4 Gb) with a Seagate Barracuda 7200 200 Gb. However the OS seems to think this is only 500 Mb and a spin speed of 5400, although it correctly recognises the drive as Seagate ST3200822A.
I take it that it still thinks the old drive is attached.... (1 Reply)
Discussion started by: wiggiesworld
1 Replies
4. Linux
Hi,
Can anyone give me the clue to my problem which is hdd not recognised when l tried to install linux enterprise edition on my laptop HP compaq nc6320 centrino.
thanxs (6 Replies)
Discussion started by: kayode
6 Replies
5. Red Hat
Hi,
I installed DirectFb on fedora 7, the machine has a Nvidia graphics card. The installation was successful and I can play the examples provided by the Direct fb website, but, I find that the accelarator is not getting recognised. when I do "fbset -i", the details shown are as below, it gives... (0 Replies)
Discussion started by: sifar
0 Replies
6. Solaris
I have a server/domain on a m5000 running Solaris 10. It is part of a cluster.
The other cluster member sees tape drives, but this one does not.
It is zoned correctly, and I can see the drives are binded in lputil.
The st.conf, and devlink.tab are identical.
ST.CONF: -
#
# Copyright... (1 Reply)
Discussion started by: pfwhufc
1 Replies
7. Shell Programming and Scripting
Hi,
my script is setting a variable with value and this variable is present in my another command that is coming from external file and this command is internally called after this variable is set. but while execution of this command, the value is not retrieved properly.
say,
my script... (5 Replies)
Discussion started by: rbalaj16
5 Replies
8. UNIX for Dummies Questions & Answers
Hi We have a redhat 4 with 8GB ram in it
but free -m only recognises 3 GB of total ram
please could some one help me why this happens
HP syetems insight manager showing 4* 2 GB RAMS
# free -m
total used free shared buffers cached
Mem: 3290... (6 Replies)
Discussion started by: robo
6 Replies
9. UNIX for Dummies Questions & Answers
Hi all
unixware 7.1.3 I'm afraid ! I connected a usb tape drive and it was automatically recognised in the device list (sdiconfig -l) and created devices in /dev/rmt (ctape1 etc.). I could successfully read and write to the device.
Then unplugged the usb cable and plugged it back in again... (0 Replies)
Discussion started by: deel
0 Replies
LEARN ABOUT MINIX
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M)
NAME
addbadsec - map out defective disk blocks
SYNOPSIS
addbadsec [-p] [ -a blkno [blkno...]] [-f filename] raw_device
DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis,
but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be
fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI
drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software
remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping.
It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block
occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup.
OPTIONS
The following options are supported:
-a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be
quoted and block numbers should be separated by white space.
-f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file.
-p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option
cannot be used to print the hardware map.
OPERANDS
The following operand is supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec,
diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to
label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 addbadsec(1M)