SHOREWALL6-TCDEVICE(5)						  [FIXME: manual]					    SHOREWALL6-TCDEVICE(5)

NAME

       tcdevices - Shorewall6 Traffic Shaping Devices file

SYNOPSIS

       /etc/shorewall6/tcdevices

DESCRIPTION

       Entries in this file define the bandwidth for interfaces on which you want traffic shaping to be enabled.

       If you do not plan to use traffic shaping for a device, don't put it in here as it limits the throughput of that device to the limits you
       set here.

       A note on the bandwidth definitions used in this file:

       o   don't use a space between the integer value and the unit: 30kbit is valid while 30 kbit is not.

       o   you can use one of the following units:

	   kbps
	       Kilobytes per second.

	   mbps
	       Megabytes per second.

	   kbit
	       Kilobits per second.

	   mbit
	       Megabits per second.

	   bps or number
	       Bytes per second.

       o   Only whole integers are allowed.

       The columns in the file are as follows (where the column name is followed by a different name in parentheses, the different name is used in
       the alternate specification syntax).

       INTERFACE - [number:]interface
	   Name of interface. Each interface may be listed only once in this file. You may NOT specify the name of an alias (e.g., eth0:0) here;
	   see http://www.shorewall.net/FAQ.htm#faq18

	   You may NOT specify wildcards here, e.g. if you have multiple ppp interfaces, you need to put them all in here!

	   If the device doesn't exist, a warning message will be issued during "shorewall6 [re]start" and "shorewall6 refresh" and traffic
	   shaping configuration will be skipped for that device.

	   Shorewall6 assigns a sequential interface number to each interface (the first entry in the file is interface 1, the second is interface
	   2 and so on) Beginning with Shorewall6-perl 4.1.6, you can explicitly specify the interface number by prefixing the interface name with
	   the number and a colon (":"). Example: 1:eth0.

       IN-BANDWIDTH (in_bandwidth) - {-|bandwidth[:burst]|~bandwidth[:interval:decay_interval]}
	   The incoming bandwidth of that interface. Please note that you are not able to do traffic shaping on incoming traffic, as the traffic
	   is already received before you could do so. But this allows you to define the maximum traffic allowed for this interface in total, if
	   the rate is exceeded, the packets are dropped. You want this mainly if you have a DSL or Cable connection to avoid queuing at your
	   providers side.

	   If you don't want any traffic to be dropped, set this to a value to zero in which case Shorewall will not create an ingress qdisc.Must
	   be set to zero if the REDIRECTED INTERFACES column is non-empty.

	   The optional burst option was added in Shorewall 4.4.18. The default burst is 10kb. A larger burst can help make the bandwidth more
	   accurate; often for fast lines, the enforced rate is well below the specified bandwidth.

	   What is described above creates a rate/burst policing filter. Beginning with Shorewall 4.4.25, a rate-estimated policing filter may be
	   configured instead. Rate-estimated filters should be used with ethernet adapters that have Generic Receive Offload enabled by default.
	   See Shorewall FAQ 97a[1].

	   To create a rate-estimated filter, precede the bandwidth with a tilde ("~"). The optional interval and decay_interval determine how
	   often the rate is estimated and how many samples are retained for estimating. Please see
	   http://ace-host.stuart.id.au/russell/files/tc/doc/estimators.txt for details.

       OUT-BANDWIDTH (out_bandwidth) - bandwidth
	   The outgoing bandwidth of that interface. This is the maximum speed your connection can handle. It is also the speed you can refer as
	   "full" if you define the tc classes in shorewall6-tcclasses[2](5). Outgoing traffic above this rate will be dropped.

       OPTIONS - {-|{classify|hfsc} ,...}
	   classify -- When specified, Shorewall will not generate tc or Netfilter rules to classify traffic based on packet marks. You must do
	   all classification using CLASSIFY rules in shorewall-tcrules[3](5).

	   hfsc - Shorewall normally uses the Hierarchical Token Bucket queuing discipline. When hfsc is specified, the Hierarchical Fair Service
	   Curves discipline is used instead.

       REDIRECTED INTERFACES (redirect) - [interface[,interface]...]
	   Added in Shorewall6-perl 4.1.6. May only be specified if the interface in the INTERFACE column is an Intermediate Frame Block (IFB)
	   device. Causes packets that enter each listed interface to be passed through the egress filters defined for this device, thus providing
	   a form of incoming traffic shaping. When this column is non-empty, the classify option is assumed.

EXAMPLES

       Example 1:
	   Suppose you are using PPP over Ethernet (DSL) and ppp0 is the interface for this. The device has an outgoing bandwidth of 500kbit and
	   an incoming bandwidth of 6000kbit

		       #INTERFACE   IN-BANDWIDTH    OUT-BANDWIDTH	  OPTIONS	  REDIRECTED
		       #								  INTERFACES
		       1:ppp0	      6000kbit	      500kbit

FILES

       /etc/shorewall6/tcdevices

SEE ALSO

       http://shorewall.net/traffic_shaping.htm

       http://ace-host.stuart.id.au/russell/files/tc/doc/estimators.txt

       shorewall6(8), shorewall6-accounting(5), shorewall6-actions(5), shorewall6-blacklist(5), shorewall6-hosts(5), shorewall6-interfaces(5),
       shorewall6-maclist(5), shoewall6-netmap(5),shorewall6-params(5), shorewall6-policy(5), shorewall6-providers(5), shorewall6-rtrules(5),
       shorewall6-routestopped(5), shorewall6-rules(5), shorewall6.conf(5), shorewall6-secmarks(5), shorewall6-tcclasses(5),
       shorewall6-tcrules(5), shorewall6-tos(5), shorewall6-tunnels(5), shorewall6-zones(5)

NOTES

	1. Shorewall FAQ 97a
	   http://www.shorewall.net/FAQ.htm#faq97a

	2. shorewall6-tcclasses
	   http://www.shorewall.net/manpages6/shorewall6-tcclasses.html

	3. shorewall-tcrules
	   http://www.shorewall.net/manpages6/shorewall-tcrules.html

[FIXME: source] 						    06/28/2012						    SHOREWALL6-TCDEVICE(5)