Sponsored Content
Operating Systems HP-UX HP-UX 10.20 Network Configure Post 302115174 by kapilraj on Sunday 22nd of April 2007 11:06:14 PM
Old 04-23-2007
Do you have a bad /etc/hosts file ? Check it.

Regards, Kaps
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

How to configure a network workstation to a standalone?

Hi, I have a networked ultra 5 workstation(using NIS) that I would like to be able to : 1. Reconfigure to standalone workstation, 2. and be able to switch back to a network workstation when the needs required. Please advise. Ryan (5 Replies)
Discussion started by: ryantk
5 Replies

2. UNIX for Dummies Questions & Answers

Need help to configure routing on home network

I have a Windows laptop and a Sparc desktop. I'm trying to toy around with routing. If have always on broadband from BT. My router ipaddress is: 192.168.1.1 This router uses DHCP. My Laptop Ip is as follows: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . :... (2 Replies)
Discussion started by: Kongowea
2 Replies

3. Solaris

how to configure network in solaris 10?

Hi..i have installed solaris 10 on vmware. I m not able connect to internet. pls help in detail. how to solve the problem. During the installation i have put no DHCP. cofigured manually ( Ip 192.168.1.9) default gateway 192.168.1.1 . (3 Replies)
Discussion started by: johnavery
3 Replies

4. Solaris

how to configure my network to use the internet

i have a router from my isp provider 02. my internet works fine in windows but i am unable to use internet in solaris. when i tried ifconfig command i was able to see the lo0 which is my laoopback adapter. pls can someone advice. (7 Replies)
Discussion started by: seyiisq
7 Replies

5. Solaris

Configure ILOM from network

HI, Is it possible to set up ILOM from the ethernet terminal. I 'm at remote location from server so would like to know if i can configure it remotely I'm able to access my server via ssh terminal. (3 Replies)
Discussion started by: fugitive
3 Replies

6. Hardware

Slackware 13.1 can't configure two network cards

Hello everybody, I'm having troubles with Slackware 13.1 and network cards. I have one on-board Ethernet card (which is recognized and works okay) and a PCI Ethernet card (which is also recognized, but doesn't appear in 'ifconfig -a'). If i run a 'lspci', i can see the kernel recognized the... (5 Replies)
Discussion started by: semash!
5 Replies

7. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

8. Solaris

Configure a network printer on solaris

Hi, guys, recently my os changed to solaris 10, and i want to share the printer with another computer whose os is also solaris. Is there anyone could give me a hint to fix this problem. lpadmin -p hp5200 -v /dev/null -A write -n... (1 Reply)
Discussion started by: papertiger
1 Replies

9. Solaris

Configure network interface for Solaris 10

Hi, I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface. Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies

10. Solaris

Configure Solaris zone on new network

Hi, I have a Solaris 10 zone which I need to configure on a new network. I have configured the new IP on the zone itself and I can ping the interface from a node on the same network, but not from another network. Basically I need to know how to route the traffic from the zone to it's... (3 Replies)
Discussion started by: sparcman
3 Replies
SYSTEMD-NETWORKD.SERVICE(8)                                  systemd-networkd.service                                  SYSTEMD-NETWORKD.SERVICE(8)

NAME
systemd-networkd.service, systemd-networkd - Network manager SYNOPSIS
systemd-networkd.service /lib/systemd/systemd-networkd DESCRIPTION
systemd-networkd is a system service that manages networks. It detects and configures network devices as they appear, as well as creating virtual network devices. To configure low-level link settings independently of networks, see systemd.link(5). systemd-networkd will create network devices based on the configuration in systemd.netdev(5) files, respecting the [Match] sections in those files. systemd-networkd will manage network addresses and routes for any link for which it finds a .network file with an appropriate [Match] section, see systemd.network(5). For those links, it will flush existing network addresses and routes when bringing up the device. Any links not matched by one of the .network files will be ignored. It is also possible to explicitly tell systemd-networkd to ignore a link by using Unmanaged=yes option, see systemd.network(5). When systemd-networkd exits, it generally leaves existing network devices and configuration intact. This makes it possible to transition from the initrams and to restart the service without breaking connectivity. This also means that when configuration is updated and systemd-networkd is restarted, netdev interfaces for which configuration was removed will not be dropped, and may need to be cleaned up manually. CONFIGURATION FILES
The configuration files are read from the files located in the system network directory /lib/systemd/network, the volatile runtime network directory /run/systemd/network and the local administration network directory /etc/systemd/network. Networks are configured in .network files, see systemd.network(5), and virtual network devices are configured in .netdev files, see systemd.netdev(5). SEE ALSO
systemd(1), systemd.link(5), systemd.network(5), systemd.netdev(5), systemd-networkd-wait-online.service(8) systemd 237 SYSTEMD-NETWORKD.SERVICE(8)
All times are GMT -4. The time now is 05:37 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy