02-15-2007
another way
you can also try:
svcs telnet
if it shows telnet is enabled , then disable it with the following command:
svcadm disable telnet
(note: This command is only for Solaris 10)
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
Can someone help me how I can disable telnet timeout? I'm connecting remotely to some machines and after some time my telnet connection was closed. How can I disable this so that I'm always connected to those machines? Thanks! (2 Replies)
Discussion started by: ayhanne
2 Replies
2. Solaris
Hi All,
I want to disable telnet on the startup of solaris 8-10 but still wants for a standby purposes. In case I need to troubleshoot ssh, I can connect thru telnet.
Most solution on the internet is to permanently removed it.
Best Regards,
itik (5 Replies)
Discussion started by: itik
5 Replies
3. Solaris
Hi...
How do I enable SSH and disable telnet..
Also - is there anything special I need to do to ensure that a new user can use ssh and su but not telnet?
Adel (15 Replies)
Discussion started by: ArabOracle.com
15 Replies
4. Solaris
On Solaris 8 is there anyway to disable telnet for a particular user and not for entire system altogether?
I would like the user to retain a shell and so creating a noshell like ftp account is not an option. (14 Replies)
Discussion started by: boshyd
14 Replies
5. Solaris
Hi,
I am unable to login into my terminal hosting Solaris 10 and get the below error message
"Server refused to allocate pty
ld.so.1: sh: fatal: libc.so.1: open failed: No such file or directory "
Is there anyways i can get into my machine and what kind of changes are required to be... (7 Replies)
Discussion started by: sankasu
7 Replies
6. Solaris
Hi
Is there anyway to disable all logs/logging (lastlog, sulog, messages etc.) in Solaris 9&10? I know this is not recommended but i just want to know if this is possible.
TIA
Reddy (8 Replies)
Discussion started by: reddyr
8 Replies
7. AIX
I need to change the security on our AIX servers and disable telnet from all but certain IP addresses.
I have hashed the telnet line in /etc/inetd.conf and added filter rules for those IP adds to allow access on port 23, but this didn't work.
Does anyone have any ideas?
Thanks. (2 Replies)
Discussion started by: Alps
2 Replies
8. Solaris
I've new installed Solaris 11 on Sparc T4-1.
I'd like to disable IPv6 but with no luck.
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
inet... (6 Replies)
Discussion started by: samer.odeh
6 Replies
9. Solaris
hello all
i have an issue about a solaris V440 cpu, im logged in the Ok prompt i can't disable a CPU3, i can't see it in dev list, i see only the cpu3-bank0 to cpu-bank4
please help me to disable it
thank youuu (3 Replies)
Discussion started by: walidadam
3 Replies
10. Solaris
Hi
I need to disable finger & telnet command in solaris 8
I have put the # infront of finger and telnet line in /etc/inetd.conf file. Further I have run the below command
kill -1 <process id of inetd >
But when I am running finger command it is till giving information for remote machine... (8 Replies)
Discussion started by: amity
8 Replies
LEARN ABOUT CENTOS
telnet-probe
TELNET-PROBE(1) General Commands Manual TELNET-PROBE(1)
NAME
telnet-probe - lightweight telnet-like port probe
SYNOPSIS
$PCP_BINADM_DIR/telnet-probe [-c] [-v] host port
DESCRIPTION
telnet-probe allows the pmdashping(1) daemons to establish connections to arbitrary local and remote service-providing daemons so that
response time and service availability information can be obtained.
The required host and port number arguments have the same meaning as their telnet(1) equivalents.
The -c option causes telnet-probe to perform a connect(2) only. This skips the read(2) and write(2) exercise that would otherwise be done
after connecting (see below).
The -v option causes telnet-probe to be verbose while operating.
Once the telnet connection has been established, telnet-probe reads from stdin until end-of-file, and writes all the input data to the tel-
net connection. Next, telnet-probe will read from the telnet connection until end-of-file, discarding whatever data it receives. Then
telnet-probe exits.
To operate successfully, the input passed via telnet-probe to the remote service must be sufficient to cause the remote service to close
the connection when the last line of input has been processed, e.g. ending with ``quit'' when probing SMTP on port 25.
By default telnet-probe will not produce any output, unless there is an error in which case a diagnostic message can be displayed (in ver-
bose mode only) and the exit status will be non-zero indicating a failure.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
DIAGNOSTICS
If telnet-probe succeeds, then 0 will be returned. If the attempt to establish a connection fails or is terminated, then a non-zero exit
status is returned.
SEE ALSO
PCPintro(1), pmdashping(1), pmie(1), telnet(1), connect(2), read(2) and write(2).
Performance Co-Pilot PCP TELNET-PROBE(1)