Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Network interface Qfe, ce, bge ...
Operating Systems Solaris Network interface Qfe, ce, bge ... Post 302094592 by nibiru78 on Monday 30th of October 2006 07:37:05 AM
Old 10-30-2006
Network Interface Names
***********************

Each physical interface is identified by a unique device name. Device names have the following syntax:

Driver names on Solaris systems could include ce, hme, bge, e1000g etc. The variable instance-number can have a value from zero to n, depending on how many interfaces of that driver type are installed on the system.

Some typical driver names for this interface are eri, qfe, and hme. When used as the primary network interface, the Fast Ethernet interface has a device name such as eri0 or qfe0
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies

3. Solaris

qfe errors and network cards

Hi All, Hope you are all doing good. In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe... (3 Replies)
Discussion started by: Krrishv
3 Replies

4. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

5. Solaris

Network Interface -- Solaris

Dear All, I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface . The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped. But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies

6. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

7. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

LEARN ABOUT OSX

systemd-networkd-wait-online.service

SYSTEMD-NETWORKD-WAIT-ONLINE.SERVICE(8) 		     systemd-networkd.service			   SYSTEMD-NETWORKD-WAIT-ONLINE.SERVICE(8)

NAME

       systemd-networkd-wait-online.service, systemd-networkd-wait-online - Wait for network to come online

SYNOPSIS

       systemd-networkd-wait-online.service

       /lib/systemd/systemd-networkd-wait-online

DESCRIPTION

       systemd-networkd-wait-online is a one-shot system service that waits for the network to be configured. By default, it will wait for all
       links it is aware of and which are managed by systemd-networkd.service(8) to be fully configured or failed, and for at least one link to
       gain a carrier.

OPTIONS

       The following options are understood:

       -i, --interface=
	   Network interface to wait for before deciding if the system is online. This is useful when a system has several interfaces which will
	   be configured, but a particular one is necessary to access some network resources. This option may be used more than once to wait for
	   multiple network interfaces. When used, all other interfaces are ignored.

       --ignore=
	   Network interfaces to be ignored when deciding if the system is online. By default, only the loopback interface is ignored. This option
	   may be used more than once to ignore multiple network interfaces.

       --timeout=
	   Fail the service if the network is not online by the time the timeout elapses. A timeout of 0 disables the timeout. Defaults to 120
	   seconds.

SEE ALSO

       systemd(1), systemd-networkd.service(8)

systemd 237												   SYSTEMD-NETWORKD-WAIT-ONLINE.SERVICE(8)
All times are GMT -4. The time now is 03:45 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy