09-27-2006
I've read about the arp command, but that is for changing the table. What I really want to do is regenerate the table without effecting any users who may be on. I've looked at inet and netgen but they say that the script should not be run manually. There must be an easier way to tell the system to go out and look for all IP's and rebuid the table. Any ideas?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
can anyone tell me the procedure to view the MAC address for a system using linux (1 Reply)
Discussion started by: tcat
1 Replies
2. IP Networking
I'm not exactly sure what I can do with IPs... my friend won't tell me(don't ask me why, I figure it's cause he doesn't know either, hehe). I'm curious as to what theya re used for other than networking computers... if there IS any other purpose or use for them. That's all.
--Evil_d00d (4 Replies)
Discussion started by: evil_d00d
4 Replies
3. UNIX for Dummies Questions & Answers
How do I change IP addresses in command mode? i need to assign custom (non DHCP) addresses from the command line. Actually I also need to know how to change the subnet mask, the gateway and the primary, secondary, ... dns servers. (6 Replies)
Discussion started by: Super.Anyak
6 Replies
4. HP-UX
I Need help !
We changed a WS HP 715/33 the new is a HP 715/100 ! The old one supports a HIL keyboard and mouse. The "new" one PS2 keyboard.
We changed only the hardware not the harddisk - now the Xserver didnīt start !
What have we to configure thatt the WS supports the PS2 keyboard under... (0 Replies)
Discussion started by: rbrandt1
0 Replies
5. Solaris
Hi all,
I've somehow gained the idea that I _need_ to run at least 1 box with Solaris, but things don't go as I had planned :-)
I pulled this ancient IBM eserver xseries 305 out of the dust, and got myself a fresh copy of the required cd's for Solaris 10u7. FAIL, for some reason the box and the... (7 Replies)
Discussion started by: mr.aart
7 Replies
6. Hardware
I am now on Kernel 2.6.32-26
For me 16x CD write speed is okay.
I have old hardware which was able to write DVDs at 1x, back in previous linux version.
Now, I dont get speed of less than 4x.
Tested on k3b, xfburn, and brasero. But all start at bottom 4x write speed. k3b forced back to... (0 Replies)
Discussion started by: makh
0 Replies
7. Solaris
Hi folk,
I have this hardware faunty message, but dont know which hardware is this ? can you guide me ?
--------------- ------------------------------------ -------------- ---------
TIME EVENT-ID MSG-ID SEVERITY
---------------... (9 Replies)
Discussion started by: dehetoxic
9 Replies
8. Shell Programming and Scripting
So I'm new to this sed command and I am trying to create a script that replaces ip addresses when I name a file but can't tweak it to work.
Here is what it looks like:
#!/bin/bash
#
file=$1
#
sed -e 's/-CPUaddr 10.30.10.166/-CPUaddr 10.30.10.151/g' -i "$file"
sed -e 's/-CPUaddr... (10 Replies)
Discussion started by: uradunce
10 Replies
9. SCO
Hello
I'm trying to virtualize an instance of Sco Unix 5.0.5 in VirtualBox (called VM-A) , but sco I have problems set to launch with the new raid controller .
The physical machine has a raid controller adaptec (alad driver) but VirtualBox uses buslogic (blc driver)
What ... (3 Replies)
Discussion started by: flako
3 Replies
10. IP Networking
Hi All,
I was told to perform analysis for IP change during a hardware refresh?
Does the IP change when a hardware refresh is performed?
if Yes, why? (5 Replies)
Discussion started by: visitsany
5 Replies
LEARN ABOUT SUNOS
conv_lpd
conv_lpd(1M) System Administration Commands conv_lpd(1M)
NAME
conv_lpd - convert LPD configuration
SYNOPSIS
conv_lpd [-c printers | -c printcap] [-n] file
DESCRIPTION
conv_lpd converts LPD printer configuration information from file to a printers.conf or a printcap file (see printers.conf(4)). file
specifies the name of the input file, and can be either in printers.conf or printcap format. If file is in printers.conf format, it con-
verts it to a printcap file. If file is in printcap format, it converts it to a printers.conf file.
OPTIONS
The following options are supported:
-c printers | -c printcap Specifies the type of output file produced by the conversion. -c printers converts to a printers.conf file.
-c printcap converts to a printcap file. -c printers is the default.
-n Preserves the namelist during the conversion.
OPERANDS
The following operands are supported:
file The file to be converted.
EXAMPLES
Example 1: Converting a printcap file to a printers.conf file.
The following example converts a printcap file to a printers.conf file.
example% conv_lpd /etc/printcap
Example 2: Converting a printcap file to a printers.conf file and preserving the namelist.
The following example converts a printcap file to a printers.conf file and preserves the namelist.
example% conv_lpd -c printers -n /etc/printcap
Example 3: Converting a printers.conf file to a printcap file and preserving the namelist.
The following example converts a printers.conf file to a printcap file and preserves the namelist.
example% conv_lpd -c printcap -n /etc/printers.conf
EXIT STATUS
The following exit values are returned:
0 Successful completion.
non-zero An error occurred.
FILES
/etc/printers.conf System printer configuration database.
/etc/printcap SunOS 4.x printer capability database.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWpcu |
+-----------------------------+-----------------------------+
SEE ALSO
lpset(1M), printers.conf(4), attributes(5)
SunOS 5.10 9 Sep 1996 conv_lpd(1M)