Sponsored Content
Full Discussion: SSH and FTP connect slow
Top Forums UNIX for Dummies Questions & Answers SSH and FTP connect slow Post 302088676 by Aeros on Wednesday 13th of September 2006 07:05:03 PM
Old 09-13-2006
SSH and FTP connect slow

Hi again guys,

Earlier today, just all of a sudden, all SSH and FTP connections to my internal Linux box just slowed down to a crawl. After the connection/authentication though, everything was back to normal speed. Until you have to connect again. A box reboot didnt work either.

Now, from previous experience, I immediately suspected reverse DNS lookups. I added my internal PC's ip addresses to the /etc/hosts file, and the problem disappeared.

However, why would the problem only start today? It's been running fine without any /etc/hosts entries for weeks now, and just today it started being ridiculous.

Any ideas?
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

slow ftp

On one of of solaris 7 boxes whenever i telnet or ftp it takes sometime before i get the prompt...any quick ideas where I should look...Thanks (3 Replies)
Discussion started by: suntan
3 Replies

2. BSD

ipfw slow ssh and ftp connections

just as the title says. thanks. #General Rule Sets /sbin/ipfw add 0300 check-state /sbin/ipfw add 0301 deny tcp from any to any in established /sbin/ipfw add 0302 pass tcp from any to any out setup keep-state /sbin/ipfw add 0303 pass udp from any to any out #SSH FTP /sbin/ipfw add 0400... (11 Replies)
Discussion started by: dwildgoose
11 Replies

3. Solaris

Solaris 9 slow login thru ssh & ftp

When I ssh to my box, an Ultra 5. I get prompted for password immediately. I enter it and have to wait sometimes a full minute for it to prompt for a password. The same thing happens when i try to ftp to the box, it will say connected, but it takes forever to prompt for password, and... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies

4. Shell Programming and Scripting

ftp script not able to connect to ftp server.

I have the following ftp script to get files from a remote location. However, on running the script I find that I am not even able to connect to ftp server. I am able to connect to ftp server using other GUI ftp tools like WS_FTP using the same IP. IP used here is a dummy IP. What can go... (3 Replies)
Discussion started by: gram77
3 Replies

5. IP Networking

Samba Slow to Connect Xp to Solaris

Hi everyone, I posted this on the Solaris forums but so far no one has been able to help... I'm new to solaris and I've installed 10, update 5. I've configured samba (very badly I believe) so that I can access my solaris box from my XP 64 computer. Both are on a local network (connected via... (1 Reply)
Discussion started by: ciscocbee
1 Replies

6. Solaris

ssh very slow

I'm facing a problem when trying to ssh to SUN servers with solaris OS,it takes a long time until prompted for password ..after connecting to the server everything work fine..how can I solve this issue??? (11 Replies)
Discussion started by: mm00123
11 Replies

7. Solaris

Slow login via SSH

Hi Guys and Girls, I know this is a common question but I've searched and we've tried the suggestions without luck. When I log into the box via SSH from a windows machine I get a 1 min 20 sec delay. If we add my IP address and machine name to /etc/hosts then I get an instant login. I would be happy... (12 Replies)
Discussion started by: MikeKulls
12 Replies

8. AIX

ftp connect in passive mode , ftp settings

how to connect to ftp server in passive mode? ftp server.abc and how can i see ftp settings, doesn't exist some ftpd.conf there is some other file where i check the options and configurations of ftp server? Thanks (3 Replies)
Discussion started by: prpkrk
3 Replies

9. HP-UX

SSH slow at connect

Hi experts, We are getting slow ssh session connections at HP-UX 11.31 servers. We have set the parameters that maybe will affect , and commented at other theads at config file sshd_config : UseDNS no X11Forwarding yes X11DisplayOffset 10 X11UseLocalhost no GSSAPIAuthentication no. ... (7 Replies)
Discussion started by: SapBasisSystem
7 Replies

10. UNIX Desktop Questions & Answers

Ftp is slow

hi, good morning. Ma trying to ftp from one AIX machine to another on the same segment of the network. The ftp to eshtablish connection from machine A to machine B is quick, but the reverse is taking is much time (2 mins). anyone can help me to solve this issue please (1 Reply)
Discussion started by: kamaldev
1 Replies
YESTERDAY(1)						      General Commands Manual						      YESTERDAY(1)

NAME
yesterday - print file names from the dump SYNOPSIS
yesterday [ -c ] [ -date ] files ... DESCRIPTION
Yesterday prints the names of the files from the most recent dump. Since dumps are done early in the morning, yesterday's files are really in today's dump. For example, if today is March 17, 1992, yesterday /adm/users prints /n/dump/1992/0317/adm/users In fact, the implementation is to select the most recent dump in the current year, so the dump selected may not be from today. With option -c, yesterday copies the dump file to the current directory. The date option selects other day's dumps, with a format of 2, 4, 6, or 8 digits of the form dd, mmdd, yymmdd, or yyyymmdd. Yesterday does not guarantee that the string it prints represents an existing file. EXAMPLES
Back up to yesterday's MIPS binary of vc: cd /mips/bin yesterday -c vc Temporarily back up to March 1's MIPS C library to see if a program runs correctly when loaded with it: bind `{yesterday -0301 /mips/lib/libc.a} /mips/lib/libc.a rm v.out mk v.out FILES
/n/dump SOURCE
/rc/bin/yesterday SEE ALSO
fs(4) BUGS
It's hard to use this command without singing. YESTERDAY(1)
All times are GMT -4. The time now is 12:54 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy