09-11-2006
what you mean with "pull image of a client on nim server" ??
10 More Discussions You Might Find Interesting
1. AIX
I try to migrate a NIM server from one server to another.
I try to do a mksysb on NIM server
restore the NIM server's mksysb to a client through NIM installation
shutdown NIM server
start newly installed client as NIM server
Does anyone do this before? who can give me some suggestion? (1 Reply)
Discussion started by: yanzhang
1 Replies
2. AIX
Hi,
I'm getting the above error while trying to take a MKSYSB image via NIM. I've only just started getting this and don't know why it is failing.
Any one got any suggestions?
Thanks
Kees (3 Replies)
Discussion started by: KeesH
3 Replies
3. AIX
Hello guys,
what is a sure-shot single command to find out if the NIM environment is working properly from both master as well as client side? (2 Replies)
Discussion started by: solaix14
2 Replies
4. AIX
Hello everyone
I have two questions.
1.-The NIM and EZNIM are the same.
2.-If I have in one partition NIM installed I need to install EZNIM or I need to unistall NIM and then install EZNIM.
Thanks for your comments. (2 Replies)
Discussion started by: lo-lp-kl
2 Replies
5. AIX
Hello All,
I believe my NIM master is fine. lsnim and cat /etc/niminfo gives me the right output. While doing "lsnim" on a client machine, I get ksh:lsnim:"not found".
Please someone be nice enough to explain what are the steps to verify the master and client connectivity to do all the NIM... (3 Replies)
Discussion started by: solaix14
3 Replies
6. AIX
Hello everyone
Im trying to backup a nim client from nim master but I got this message
COMMAND STATUS
Command: failed stdout: yes stderr: no
Before command completion, additional instructions may appear below.
0042-001 nim:... (2 Replies)
Discussion started by: lo-lp-kl
2 Replies
7. AIX
I have configured the NIM Master using AIX 5.3.7, I am getting below message bootp:bootp request fail:0 while booting nim client.
Though both system are able to ping each other.
Regards
Manoj (5 Replies)
Discussion started by: manoj.solaris
5 Replies
8. AIX
Hi.
I change my client's IP and hostname but I forgot to change anything on the master. How can I redefine or modify my client's resource from my master, or with using smit niminit from my client ?
Tks (2 Replies)
Discussion started by: stephnane
2 Replies
9. AIX
Hello, I have an AIX6.1 machine which is a nim client to my nim master which is also AIX6.1 machine. I had some problem to perform an installation on my client using smit nim . i removed /etc/niminfo file in order to do the initialization again but when i run the command niminit -a name=client... (0 Replies)
Discussion started by: omonoiatis9
0 Replies
10. AIX
Friend's,
I was playing around with NIM in my environment & had a quick question in mind which I didn't/couldn't find answer to, which is -- how to find the name of the NIM server sitting on the NIM client?
All leads to the answer would be much appreciated, many thanks!
-- Souvik (2 Replies)
Discussion started by: thisissouvik
2 Replies
LEARN ABOUT DEBIAN
smd-server
smd-server(1) Sync Mail Dir (smd) documentation smd-server(1)
NAME
smd-server - sends diffs and mails to smd-client
SYNOPSIS
smd-server [--exclude glob] [-v|--verbose] [-d|--dry-run]
[--get-mddiff-cmdline] [--stop-after-diff]
[--override-db dbf] [--dump-stdin tgt] endpoint mailboxes
DESCRIPTION
smd-server needs to know a name (endpoint) for the client (that must not be used by others) and a list of mailboxes (directories).
smd-server first calls mddiff(1), then prints on stdout the generated diff. It then accepts from stdin a small set of commands a client may
issue to request a file (or parts of it, like the header).
smd-server is in charge of committing the db file used by mddiff(1) in case the client communicates a successful sync.
OPTIONS
-v --verbose
Increase program verbosity (printed on stderr)
-d --dry-run
Do not perform any action for real
-n --no-delete
Do not track deleted files
--exclude glob
Exclude paths matching glob
--override-db dbf
Use dbf as the db-file
--get-mddiff-cmdline
Print the command line used for mddiff and then exist
--stop-after-diff
Send the actions to the other endpoint and exit. If used in conjunction with --override-db, dbf is removed just before exiting
--dump-stdin tgt
Dump standard input to tgt and exit
NOTES
smd-server is a low level utility. You should use higher level tools like smd-pull(1) and smd-push(1)
SEE ALSO
mddiff(1), smd-client(1), smd-pull(1), smd-push(1)
AUTHOR
Enrico Tassi <gares@fettunta.org>
11 June 2012 smd-server(1)