09-08-2006
Thanks Blowtorch, this seems to have worked.
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
We have SunOS 5.7 m/c. Following is the situation and problem what we are facing -
- The root partition was full.
- No login was possible on server (not from console also)
- M/c was power swithced off
- After this only console login is possible. FTP is possible. No telnet is possible.
I... (3 Replies)
Discussion started by: rahul72
3 Replies
2. UNIX for Advanced & Expert Users
We have SunOS 5.7 m/c. Following is the situation and problem what we are facing -
- The root partition was full.
- No login was possible on server (not from console also)
- M/c was power swithced off
- After this only console login is possible. FTP is possible. No telnet is possible.
I... (1 Reply)
Discussion started by: rahul72
1 Replies
3. UNIX for Dummies Questions & Answers
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Discussion started by: jtp51
1 Replies
4. UNIX for Advanced & Expert Users
HI,
Currently I am working in One of the webhosting company and I found
on one of my server "/home" partition is getting full say 105% usage...
But when I actually check the partition size using "du -h", exact partition
utilization is only 60-70%.
So... (1 Reply)
Discussion started by: jagdish.machhi@
1 Replies
5. HP-UX
hi,
I want to know that "What Happen if the root partition gets full on the server? I have HP-Unix 11.11 installed. (3 Replies)
Discussion started by: majidtahir
3 Replies
6. HP-UX
My /var partition is almost utilized ... Here am not sure where to release space now
OS/model : HP-UX B.11.11 U 9000/800
# bdf /var
Filesystem kbytes used avail %used Mounted on
/dev/vg00/lvol9 6144000 6142176 1824 100% /var
<root@pb>/var # du -sk * | sort -n |... (20 Replies)
Discussion started by: Shirishlnx
20 Replies
7. Solaris
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies
8. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
9. UNIX for Beginners Questions & Answers
Good day,
Anybody, know how to clean/free up the Cluster_boot partition in TRU64
Thank you in advance
Miaka (0 Replies)
Discussion started by: miaka1012
0 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
chown(1), mknod(1), sd(4), mount(8)
COLOPHON
This page is part of release 3.25 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 HD(4)