06-20-2006
SOLARIS does not route
hi,
i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan, the SOLARIS does not route. and i do not find the problem.
lan1 - SOLARIS - lan2
lan1: 192.168.100.0 - 255.255.255.0
lan2: 10.0.0.0 - 255.255.255.0
interface1: 192.168.100.6
interface2: 10.0.0.6
file /etc/notrouter does not exist.
here are the outputs of the ifconfig and netstat commands:
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.0.0.6 netmask ffffff00 broadcast 10.0.0.255
ether 0:3:ba:60:ac:1b
bge1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 192.168.100.6 netmask ffffff00 broadcast 192.168.100.255
ether 0:3:ba:60:ac:1c
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
-------------------- -------------------- ----- ----- ------ ---------
192.168.100.0 192.168.100.6 U 1 4 bge1
10.0.0.0 10.0.0.6 U 1 3 bge0
127.0.0.1 127.0.0.1 UH 2 6 lo0
any ideas? thanks for helping.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Dear Friends, I'm here again
I need to know where is the permanent file for gateway configuration.
I did the following command
route add -net 0.0.0.0 5.0.0.3 ( My Gateway), but when i restart my computer i have to do it again.
What the file can i set the permanent configuration for my... (1 Reply)
Discussion started by: themask
1 Replies
2. Solaris
I am having problems getting this to work, though it seems like it would be simple. I have a host with 2 interfaces, hme0 (192.168.0.132) for the primary interface, and hme1 (192.168.0.16) for backups. I want it to talk to the backup host, which is 192.168.0.21, across the hme1 interface.
Thanks (2 Replies)
Discussion started by: 98_1LE
2 Replies
3. IP Networking
WE are running Unix - Solaris 2.6, we create a subnet. In the windows enviroment we are able to add a static route by using
route add -p 172.16.10.0 mask 255.255.255.0 172.16.17.224, but when we add the route in Solaris as
route add -net 172.16.10.0 255.255.255.0 172.16.17.224, we receive an... (5 Replies)
Discussion started by: cassy
5 Replies
4. Solaris
Hi,
Any one can help me in this below mentioned issue I am facing in my solaris server?
here the scenario goes....
i have multiple segments in my LAN like remote csr, database, production etc. and all the segments are configured in Windows/CISCo network.
from my all system in remote... (1 Reply)
Discussion started by: Praan
1 Replies
5. Solaris
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies
6. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
7. Solaris
Hey Guys.
I am trying include a route on the Sun Solaris 10 System an get the follow respond:
Network is unreachable.
Let me show the command.
root@ColectorDMSCNT # route add 200.44.46.0/27 161.196.84.193 1
add net 200.44.46.0/27: gateway 161.196.84.193: Network is unreachable
... (1 Reply)
Discussion started by: aggadtech08
1 Replies
8. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
9. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
10. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
LEARN ABOUT HPUX
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)