06-20-2006
SOLARIS does not route
hi,
i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan, the SOLARIS does not route. and i do not find the problem.
lan1 - SOLARIS - lan2
lan1: 192.168.100.0 - 255.255.255.0
lan2: 10.0.0.0 - 255.255.255.0
interface1: 192.168.100.6
interface2: 10.0.0.6
file /etc/notrouter does not exist.
here are the outputs of the ifconfig and netstat commands:
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.0.0.6 netmask ffffff00 broadcast 10.0.0.255
ether 0:3:ba:60:ac:1b
bge1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 192.168.100.6 netmask ffffff00 broadcast 192.168.100.255
ether 0:3:ba:60:ac:1c
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
-------------------- -------------------- ----- ----- ------ ---------
192.168.100.0 192.168.100.6 U 1 4 bge1
10.0.0.0 10.0.0.6 U 1 3 bge0
127.0.0.1 127.0.0.1 UH 2 6 lo0
any ideas? thanks for helping.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Dear Friends, I'm here again
I need to know where is the permanent file for gateway configuration.
I did the following command
route add -net 0.0.0.0 5.0.0.3 ( My Gateway), but when i restart my computer i have to do it again.
What the file can i set the permanent configuration for my... (1 Reply)
Discussion started by: themask
1 Replies
2. Solaris
I am having problems getting this to work, though it seems like it would be simple. I have a host with 2 interfaces, hme0 (192.168.0.132) for the primary interface, and hme1 (192.168.0.16) for backups. I want it to talk to the backup host, which is 192.168.0.21, across the hme1 interface.
Thanks (2 Replies)
Discussion started by: 98_1LE
2 Replies
3. IP Networking
WE are running Unix - Solaris 2.6, we create a subnet. In the windows enviroment we are able to add a static route by using
route add -p 172.16.10.0 mask 255.255.255.0 172.16.17.224, but when we add the route in Solaris as
route add -net 172.16.10.0 255.255.255.0 172.16.17.224, we receive an... (5 Replies)
Discussion started by: cassy
5 Replies
4. Solaris
Hi,
Any one can help me in this below mentioned issue I am facing in my solaris server?
here the scenario goes....
i have multiple segments in my LAN like remote csr, database, production etc. and all the segments are configured in Windows/CISCo network.
from my all system in remote... (1 Reply)
Discussion started by: Praan
1 Replies
5. Solaris
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies
6. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
7. Solaris
Hey Guys.
I am trying include a route on the Sun Solaris 10 System an get the follow respond:
Network is unreachable.
Let me show the command.
root@ColectorDMSCNT # route add 200.44.46.0/27 161.196.84.193 1
add net 200.44.46.0/27: gateway 161.196.84.193: Network is unreachable
... (1 Reply)
Discussion started by: aggadtech08
1 Replies
8. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
9. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
10. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
LEARN ABOUT FREEBSD
ntb_hw
NTB(4) BSD Kernel Interfaces Manual NTB(4)
NAME
ntb, ntb_hw, if_ntb -- Intel(R) Non-Transparent Bridge driver
SYNOPSIS
To compile this driver into your kernel, place the following lines in your kernel configuration file:
device ntb_hw
device if_ntb
Or, to load the driver as a module at boot, place the following line in loader.conf(5):
if_ntb_load="YES"
DESCRIPTION
The ntb driver provides support for the Non-Transparent Bridge (NTB) in the Intel S1200, Xeon E3 and Xeon E5 processor families.
The NTB allows you to connect two computer systems using a PCI-e link if they have the correct equipment and connectors.
CONFIGURATION
The NTB memory windows need to be configured by the BIOS. If your BIOS allows you to set their size, you should set the size of both memory
windows to 1 MiB. This needs to be done on both systems.
Each system needs to have a different IP address assigned. The MAC address is randomly generated. Also for maximum performance, the MTU
should be set to 16 kiB. This can be done by adding the line below to rc.conf(5):
ifconfig_ntb0="inet 192.168.1.10 netmask 255.255.255.0 mtu 16384"
And on the second system :
ifconfig_ntb0="inet 192.168.1.11 netmask 255.255.255.0 mtu 16384"
If you are using the UDP protocol, you may want to increase the net.inet.udp.maxdgram sysctl(8) variable.
SEE ALSO
rc.conf(5), sysctl(8)
AUTHORS
The ntb driver was developed by Intel and originally written by Carl Delsey <carl@FreeBSD.org>.
BUGS
If the driver is unloaded, it cannot be reloaded without a system reboot.
The network support is limited. It isn't fully configurable yet. It also isn't integrated into netgraph(4) or bpf(4).
NTB to Root Port mode is not yet supported.
There is no way to protect your system from malicious behavior on the other system once the link is brought up. Anyone with root or kernel
access on the other system can read or write to any location on your system. In other words, only connect two systems that completely trust
each other.
BSD
Apr 11, 2013 BSD