10-14-2002
help installing Sun 8mm unipack scsi tape drive
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the tape is not found.
Whatever backup commands I issued such as mt, tar, or ufsdump, I would just get "/dev/rmt/0n no device or address" message.
Here are questions hoping you can help out:
1. do I need to do any configuration to prepare tape drive for use? such as mounting?
2. what other methods can I use to verify that the tape drive is recognized by O/S and ready to be used.
my system info:
Sun Ultra 5 running solaris 7
Thanks in advance for your help.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm running SCO OS 505 on a Compaq proliant 1600, and my tape drive will just not work. It was working properly and whent to Sh?ts when I tried to get the cd rom working. I have uninstalled any configured tape drive and rebooted and then configured a tape drive and rebooted still nothing. I'm... (4 Replies)
Discussion started by: kikkin
4 Replies
2. UNIX for Dummies Questions & Answers
hello,
I don't know what exactly the cause and the solution!!
suddenly I receive this error message when I want to use the 8mm tape drive
"I/O write error"
I disconnect the tape drive and I hook it in another WS and I receive this error :- ... (5 Replies)
Discussion started by: geoquest
5 Replies
3. Filesystems, Disks and Memory
I'm researching a tape drive + backup software to work across my unix/linux network. Was thinking about a dds4 tape drive (sony's) on my solaris ultra2, with some kind of software that would work across the network to back up my other 2 solaris boxes, plus my 2 linux boxes. What do others use... (3 Replies)
Discussion started by: kymberm
3 Replies
4. Solaris
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies
5. Solaris
Hi,
I am a newbie to Solaris, I have a SunFire V120 box, i was trying to install a tape drive(HP SureStore DAT24), i did the install in this manner.
# rm -rf /etc/path_to_inst
# init 6
later at the "ok" prompt i gave "boot -ar" after doing that it asked me various options i accepted the... (2 Replies)
Discussion started by: rajendra.rait
2 Replies
6. Linux
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Discussion started by: RuralTurtle
0 Replies
7. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
8. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
9. Hardware
I've had a scsi hard drive, scsi tape drive, and cd rom working off an adaptec 29160 controller. Everything worked great until a few days ago. I begin getting tar format errors (running sco 5.0.6) on the tape drive and occasionally the entire system would hang up while trying to access data on... (0 Replies)
Discussion started by: powwm
0 Replies
10. Solaris
Hi all,
this time I'd need a help from an advanced Solaris system admin :rolleyes:
I attached a HP StorageWorks Ultrium 215 Tape Drives - Overview - c00059530 - HP Business Support Center to my Sun E220R and it got recognized immediately (probe-scsi-all).
Now the operating system boot process... (8 Replies)
Discussion started by: pseudocoder
8 Replies
tms(4) Kernel Interfaces Manual tms(4)
Name
tms - TMSCP magnetic tape interface
Syntax
For UNIBUS, Q-bus:
controller klesiu0 at uba0
controller uq0 at klesiu0 csr 0174500 vector uqintr
tape tms0 at uq0 drive 0
For MSI Bus:
adapter msi0 at nexus?
controller dssc0 at msi0 msinode 0
tape tms0 at dssc0 drive 3
For VAXBI:
controller klesib0 at vaxbi0 node 0
controller uq0 at klesib0 vector uqintr
tape tms0 at uq0 drive 0
controller aie0 at vaxbi? node?
controller bvpssp0 at aie0 vector bvpsspintr
tape tms0 at bvpssp0 drive 0
For MSI Bus:
adapter msi0 at nexus?
controller dssc0 at msi0 msinode 0
tape tms0 at dssc0 drive 0
For VAX CI/HSC:
adapter ci0 at nexus?
adapter ci0 at vaxbi? node?
controller hsc0 at ci0 cinode 6
tape tms0 at hsc0 drive 3
Description
Prior to Version 2.0, this device was referenced by tmscp(4).
The TMSCP driver provides a standard tape drive interface, as described in This is a driver for any controller that adheres to the Tape
Mass Storage Control Protocol (TMSCP). The TMSCP controllers communicate with the host through a packet-oriented protocol termed the Tape
Mass Storage Control Protocol. This driver also supports n-buffered reads and writes to the raw tape interface (used with streaming tape
drives). See for further details.
Tape Support
TK50, TK70, TF70, TU81, TU81e, TA78, TA79, TA81, RV20, TA90, TA90E, TA91
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
Files
See Also
mtio(4), nbuf(4), MAKEDEV(8), uerf(8), tapex(8)
Guide to the Error Logger
tms(4)